Broadcom wireless not working in statler 2011-12

joksim · 2011-12-09 15:18:29

I do not get it. Create 2 files edit and broadcom-sta.conf?

I guess I should insert it for the file:
/etc/modprobe.d/broadcom-sta-common.conf ?

xaos52 · 2011-12-09 15:20:00

Thats correct. I have edited my post already.

joksim · 2011-12-09 15:36:13

No luck at all.
Now I don't even have a wireless entry in networkmanager right-click.

interestingly, when I run lspci -vnn i get:

 04:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
    Subsystem: Hewlett-Packard Company BCM4311 802.11b/g Wireless LAN Controller [103c:1364]
    Flags: bus master, fast devsel, latency 0, IRQ 18
    Memory at d5100000 (32-bit, non-prefetchable) [size=16K]
    Capabilities: <access denied>
    Kernel driver in use: wl

so wl is in use, but it's not working...

output from lsmod:

Module                  Size  Used by
acpi_cpufreq           12849  0 
mperf                  12411  1 acpi_cpufreq
cpufreq_conservative    13147  0 
cpufreq_userspace      12576  0 
cpufreq_stats          12762  0 
cpufreq_powersave      12454  0 
parport_pc             22191  0 
ppdev                  12725  0 
lp                     17190  0 
parport                31650  3 parport_pc,ppdev,lp
bridge                 65614  0 
stp                    12392  1 bridge
bnep                   17424  2 
rfcomm                 32744  0 
bluetooth             107224  10 bnep,rfcomm
fuse                   61554  3 
loop                   22479  0 
firewire_sbp2          17825  0 
wl                   2678027  1 
snd_hda_codec_hdmi     22174  1 
snd_hda_codec_realtek   283734  1 
joydev                 17138  0 
uvcvideo               57386  0 
videodev               66266  1 uvcvideo
media                  18148  1 videodev
snd_hda_intel          25946  1 
snd_hda_codec          67865  3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel
snd_seq                44678  0 
v4l2_compat_ioctl32    16575  1 videodev
snd_seq_device         13155  1 snd_seq
snd_hwdep              13148  1 snd_hda_codec
fglrx                3036748  84 
snd_pcm                67276  3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
snd_timer              22658  2 snd_seq,snd_pcm
ideapad_laptop         12892  0 
i2c_i801               16870  0 
tpm_tis                13125  0 
acer_wmi               21843  0 
tpm                    17756  1 tpm_tis
snd                    52324  11 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_seq,snd_seq_device,snd_hwdep,snd_pcm,snd_timer
sparse_keymap          12760  2 ideapad_laptop,acer_wmi
cfg80211              126244  1 wl
soundcore              13014  1 snd
battery                13109  0 
ac                     12624  0 
r852                   17768  0 
sm_common              16450  1 r852
nand                   44305  2 r852,sm_common
nand_ids               12313  1 nand
nand_ecc               12444  1 nand
psmouse                55199  0 
mtd                    24058  2 sm_common,nand
tpm_bios               12903  1 tpm
rfkill                 19014  5 bluetooth,ideapad_laptop,acer_wmi,cfg80211
lib80211               12990  1 wl
i2c_core               23766  2 videodev,i2c_i801
video                  17553  0 
snd_page_alloc         12969  2 snd_hda_intel,snd_pcm
serio_raw              12878  0 
evdev                  17475  16 
pcspkr                 12579  0 
processor              27431  3 acpi_cpufreq
power_supply           13475  2 battery,ac
wmi                    13202  1 acer_wmi
button                 12895  1 fglrx
ext4                  313064  3 
mbcache                12930  1 ext4
jbd2                   65105  1 ext4
crc16                  12343  2 bluetooth,ext4
sg                     25769  0 
sr_mod                 21824  0 
sd_mod                 35644  5 
cdrom                  35134  1 sr_mod
usbhid                 39946  0 
crc_t10dif             12348  1 sd_mod
hid                    72745  1 usbhid
uhci_hcd               26290  0 
ahci                   25089  4 
libahci                22616  1 ahci
libata                151572  2 ahci,libahci
sdhci_pci              13184  0 
tg3                   109263  0 
firewire_ohci          35027  0 
ehci_hcd               39487  0 
scsi_mod              161557  5 firewire_sbp2,sg,sr_mod,sd_mod,libata
sdhci                  21685  1 sdhci_pci
mmc_core               58824  1 sdhci
usbcore               127203  5 uvcvideo,usbhid,uhci_hcd,ehci_hcd
firewire_core          47790  2 firewire_sbp2,firewire_ohci
thermal                17330  0 
libphy                 18759  1 tg3
crc_itu_t              12347  1 firewire_core
thermal_sys            17939  3 video,processor,thermal

xaos52 · 2011-12-09 15:40:25

dmesg output?

joksim · 2011-12-09 15:43:14

dmesg ouput:

joksim@joksimU330:~$ dmesg 
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.39-bpo.2-amd64 (Debian 2.6.39-3~bpo60+1) (norbert@tretkowski.de) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Tue Jul 26 10:35:23 UTC 2011
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.39-bpo.2-amd64 root=UUID=7fc0180d-b927-4df4-bbee-c5cd8cb0278f ro quiet splash
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bdee1000 (usable)
[    0.000000]  BIOS-e820: 00000000bdee1000 - 00000000bdee4000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bdee4000 - 00000000bfd04000 (usable)
[    0.000000]  BIOS-e820: 00000000bfd04000 - 00000000bfd3f000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bfd3f000 - 00000000bfd6a000 (usable)
[    0.000000]  BIOS-e820: 00000000bfd6a000 - 00000000bfdbf000 (reserved)
[    0.000000]  BIOS-e820: 00000000bfdbf000 - 00000000bfdeb000 (usable)
[    0.000000]  BIOS-e820: 00000000bfdeb000 - 00000000bfdff000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bfdff000 - 00000000bfe00000 (usable)
[    0.000000]  BIOS-e820: 00000000bfe00000 - 00000000c0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff800000 - 00000000ff801000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff810000 - 00000000ff810100 (reserved)
[    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.4 present.
[    0.000000] DMI: LENOVO INVALID/Base Board Product Name, BIOS 0FCN67WW 09/16/2009
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0xbfe00 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-CFFFF uncachable
[    0.000000]   D0000-D7FFF write-protect
[    0.000000]   D8000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0FFE00000 mask FFFE00000 write-protect
[    0.000000]   1 base 000000000 mask F80000000 write-back
[    0.000000]   2 base 080000000 mask FC0000000 write-back
[    0.000000]   3 base 0BFE00000 mask FFFE00000 uncachable
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-00000000bfe00000
[    0.000000]  0000000000 - 00bfe00000 page 2M
[    0.000000] kernel direct mapping tables up to bfe00000 @ bfde7000-bfdeb000
[    0.000000] RAMDISK: 37676000 - 37ff0000
[    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 LENOVO)
[    0.000000] ACPI: XSDT 00000000bfdfe120 0006C (v01 LENOVO CB-01    00000001      01000013)
[    0.000000] ACPI: FACP 00000000bfdfd000 000F4 (v04 LENOVO CB-01    00000001 MSFT 000F4240)
[    0.000000] ACPI: DSDT 00000000bfdf1000 07D1B (v01 INSYDE Montevin 00000001 INTL 20051117)
[    0.000000] ACPI: FACS 00000000bfd12000 00040
[    0.000000] ACPI: HPET 00000000bfdfc000 00038 (v01 LENOVO CB-01    00000001 MSFT 000F4240)
[    0.000000] ACPI: APIC 00000000bfdfb000 0006C (v02 INSYDE          00000001 TFSM 000F4240)
[    0.000000] ACPI: MCFG 00000000bfdfa000 0003C (v01 INSYDE          00000001 TFSM 000F4240)
[    0.000000] ACPI: ASF! 00000000bfdf9000 000A5 (v32 INTEL       HCG 00000001 TFSM 000F4240)
[    0.000000] ACPI: SLIC 00000000bfdf0000 00176 (v01 LENOVO CB-01    00000001 LNVO 00000001)
[    0.000000] ACPI: BOOT 00000000bfdef000 00028 (v01 INSYDE INSYDE   00000001    ? 00000001)
[    0.000000] ACPI: SSDT 00000000bfdee000 002C6 (v01 INTEL  SataAhci 00001000 INTL 20051117)
[    0.000000] ACPI: SSDT 00000000bfdeb000 00655 (v01  PmRef    CpuPm 00003000 INTL 20051117)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-00000000bfe00000
[    0.000000] NUMA: Using 63 for the hash shift.
[    0.000000] Initmem setup node 0 0000000000000000-00000000bfe00000
[    0.000000]   NODE_DATA [00000000bfde2000 - 00000000bfde6fff]
[    0.000000]  [ffffea0000000000-ffffea00029fffff] PMD -> [ffff8800bae00000-ffff8800bd7fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   empty
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[6] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x000bdee1
[    0.000000]     0: 0x000bdee4 -> 0x000bfd04
[    0.000000]     0: 0x000bfd3f -> 0x000bfd6a
[    0.000000]     0: 0x000bfdbf -> 0x000bfdeb
[    0.000000]     0: 0x000bfdff -> 0x000bfe00
[    0.000000] On node 0 totalpages: 785640
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3922 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10689 pages used for memmap
[    0.000000]   DMA32 zone: 770968 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000bdee1000 - 00000000bdee4000
[    0.000000] PM: Registered nosave memory: 00000000bfd04000 - 00000000bfd3f000
[    0.000000] PM: Registered nosave memory: 00000000bfd6a000 - 00000000bfdbf000
[    0.000000] PM: Registered nosave memory: 00000000bfdeb000 - 00000000bfdff000
[    0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 28 pages/cpu @ffff8800bfa00000 s83840 r8192 d22656 u524288
[    0.000000] pcpu-alloc: s83840 r8192 d22656 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 774890
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.39-bpo.2-amd64 root=UUID=7fc0180d-b927-4df4-bbee-c5cd8cb0278f ro quiet splash
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 3080900k/3143680k available (3315k kernel code, 1120k absent, 61660k reserved, 3375k data, 596k init)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]     RCU-based detection of stalled CPUs is disabled.
[    0.000000] NR_IRQS:33024 nr_irqs:712 16
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1995.009 MHz processor.
[    0.004004] Calibrating delay loop (skipped), value calculated using timer frequency.. 3990.01 BogoMIPS (lpj=7980036)
[    0.004009] pid_max: default: 32768 minimum: 301
[    0.004094] Security Framework initialized
[    0.004099] SELinux:  Disabled at boot.
[    0.004470] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.009829] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.010974] Mount-cache hash table entries: 256
[    0.011131] Initializing cgroup subsys ns
[    0.011136] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[    0.011139] Initializing cgroup subsys cpuacct
[    0.011143] Initializing cgroup subsys memory
[    0.011156] Initializing cgroup subsys devices
[    0.011158] Initializing cgroup subsys freezer
[    0.011162] Initializing cgroup subsys net_cls
[    0.011164] Initializing cgroup subsys blkio
[    0.011211] CPU: Physical Processor ID: 0
[    0.011213] CPU: Processor Core ID: 0
[    0.011215] mce: CPU supports 6 MCE banks
[    0.011223] CPU0: Thermal monitoring enabled (TM2)
[    0.011228] using mwait in idle threads.
[    0.012434] ACPI: Core revision 20110316
[    0.020076] Setting APIC routing to flat
[    0.020390] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.063164] CPU0: Intel(R) Core(TM)2 Duo CPU     P7350  @ 2.00GHz stepping 06
[    0.064003] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[    0.064003] ... version:                2
[    0.064003] ... bit width:              40
[    0.064003] ... generic registers:      2
[    0.064003] ... value mask:             000000ffffffffff
[    0.064003] ... max period:             000000007fffffff
[    0.064003] ... fixed-purpose events:   3
[    0.064003] ... event mask:             0000000700000003
[    0.064003] NMI watchdog enabled, takes one hw-pmu counter.
[    0.064003] Booting Node   0, Processors  #1
[    0.064003] smpboot cpu 1: start_ip = 9a000
[    0.152038] NMI watchdog enabled, takes one hw-pmu counter.
[    0.152078] Brought up 2 CPUs
[    0.152080] Total of 2 processors activated (7980.00 BogoMIPS).
[    0.153301] devtmpfs: initialized
[    0.156693] PM: Registering ACPI NVS region at bdee1000 (12288 bytes)
[    0.156693] PM: Registering ACPI NVS region at bfd04000 (241664 bytes)
[    0.156693] print_constraints: dummy: 
[    0.156693] NET: Registered protocol family 16
[    0.156693] ACPI: bus type pci registered
[    0.156693] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.156693] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.166062] PCI: Using configuration type 1 for base access
[    0.166494] bio: create slab <bio-0> at 0
[    0.168356] ACPI: EC: Look up EC in DSDT
[    0.193044] ACPI: Executed 1 blocks of module-level executable AML code
[    0.194370] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.194943] ACPI: SSDT 00000000bfd76c98 00223 (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
[    0.195329] ACPI: Dynamic OEM Table Load:
[    0.195332] ACPI: SSDT           (null) 00223 (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
[    0.195528] ACPI: SSDT 00000000bfd74598 00537 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
[    0.195891] ACPI: Dynamic OEM Table Load:
[    0.195894] ACPI: SSDT           (null) 00537 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
[    0.216379] ACPI: SSDT 00000000bfd75e18 001CF (v01  PmRef    ApIst 00003000 INTL 20051117)
[    0.216785] ACPI: Dynamic OEM Table Load:
[    0.216788] ACPI: SSDT           (null) 001CF (v01  PmRef    ApIst 00003000 INTL 20051117)
[    0.228170] ACPI: SSDT 00000000bfd76f18 0008D (v01  PmRef    ApCst 00003000 INTL 20051117)
[    0.228549] ACPI: Dynamic OEM Table Load:
[    0.228551] ACPI: SSDT           (null) 0008D (v01  PmRef    ApCst 00003000 INTL 20051117)
[    0.248130] ACPI: Interpreter enabled
[    0.248133] ACPI: (supports S0 S3 S4 S5)
[    0.248169] ACPI: Using IOAPIC for interrupt routing
[    0.265940] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.288160] ACPI: No dock devices found.
[    0.288162] HEST: Table not found.
[    0.288165] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.288543] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.289285] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
[    0.289288] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
[    0.289291] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.289295] pci_root PNP0A08:00: host bridge window [mem 0xc0000000-0xfebfffff]
[    0.289307] pci 0000:00:00.0: [8086:2a40] type 0 class 0x000600
[    0.289328] DMAR: Forcing write-buffer flush capability
[    0.289330] DMAR: Disabling IOMMU for graphics on this chipset
[    0.289353] pci 0000:00:01.0: [8086:2a41] type 1 class 0x000604
[    0.289384] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.289388] pci 0000:00:01.0: PME# disabled
[    0.289432] pci 0000:00:1a.0: [8086:2937] type 0 class 0x000c03
[    0.289495] pci 0000:00:1a.0: reg 20: [io  0x70e0-0x70ff]
[    0.289559] pci 0000:00:1a.1: [8086:2938] type 0 class 0x000c03
[    0.289622] pci 0000:00:1a.1: reg 20: [io  0x70c0-0x70df]
[    0.289677] pci 0000:00:1a.2: [8086:2939] type 0 class 0x000c03
[    0.289735] pci 0000:00:1a.2: reg 20: [io  0x70a0-0x70bf]
[    0.289805] pci 0000:00:1a.7: [8086:293c] type 0 class 0x000c03
[    0.289826] pci 0000:00:1a.7: reg 10: [mem 0xd8204c00-0xd8204fff]
[    0.289901] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    0.289906] pci 0000:00:1a.7: PME# disabled
[    0.289930] pci 0000:00:1b.0: [8086:293e] type 0 class 0x000403
[    0.289946] pci 0000:00:1b.0: reg 10: [mem 0xd8200000-0xd8203fff 64bit]
[    0.290002] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.290006] pci 0000:00:1b.0: PME# disabled
[    0.290026] pci 0000:00:1c.0: [8086:2940] type 1 class 0x000604
[    0.290083] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.290087] pci 0000:00:1c.0: PME# disabled
[    0.290109] pci 0000:00:1c.1: [8086:2942] type 1 class 0x000604
[    0.290166] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.290170] pci 0000:00:1c.1: PME# disabled
[    0.290192] pci 0000:00:1c.2: [8086:2944] type 1 class 0x000604
[    0.290249] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.290253] pci 0000:00:1c.2: PME# disabled
[    0.290275] pci 0000:00:1c.3: [8086:2946] type 1 class 0x000604
[    0.290331] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.290336] pci 0000:00:1c.3: PME# disabled
[    0.290364] pci 0000:00:1d.0: [8086:2934] type 0 class 0x000c03
[    0.290425] pci 0000:00:1d.0: reg 20: [io  0x7080-0x709f]
[    0.290489] pci 0000:00:1d.1: [8086:2935] type 0 class 0x000c03
[    0.290552] pci 0000:00:1d.1: reg 20: [io  0x7060-0x707f]
[    0.290616] pci 0000:00:1d.2: [8086:2936] type 0 class 0x000c03
[    0.290672] pci 0000:00:1d.2: reg 20: [io  0x7040-0x705f]
[    0.290739] pci 0000:00:1d.7: [8086:293a] type 0 class 0x000c03
[    0.290760] pci 0000:00:1d.7: reg 10: [mem 0xd8204800-0xd8204bff]
[    0.290835] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.290840] pci 0000:00:1d.7: PME# disabled
[    0.290861] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[    0.290920] pci 0000:00:1f.0: [8086:2919] type 0 class 0x000601
[    0.291033] pci 0000:00:1f.2: [8086:2929] type 0 class 0x000106
[    0.291052] pci 0000:00:1f.2: reg 10: [io  0x7108-0x710f]
[    0.291061] pci 0000:00:1f.2: reg 14: [io  0x7114-0x7117]
[    0.291069] pci 0000:00:1f.2: reg 18: [io  0x7100-0x7107]
[    0.291078] pci 0000:00:1f.2: reg 1c: [io  0x7110-0x7113]
[    0.291086] pci 0000:00:1f.2: reg 20: [io  0x7020-0x703f]
[    0.291095] pci 0000:00:1f.2: reg 24: [mem 0xd8204000-0xd82047ff]
[    0.291129] pci 0000:00:1f.2: PME# supported from D3hot
[    0.291133] pci 0000:00:1f.2: PME# disabled
[    0.291151] pci 0000:00:1f.3: [8086:2930] type 0 class 0x000c05
[    0.291167] pci 0000:00:1f.3: reg 10: [mem 0xd8205000-0xd82050ff 64bit]
[    0.291190] pci 0000:00:1f.3: reg 20: [io  0x7000-0x701f]
[    0.291251] pci 0000:01:00.0: [1002:95c4] type 0 class 0x000300
[    0.291263] pci 0000:01:00.0: reg 10: [mem 0xc0000000-0xcfffffff pref]
[    0.291271] pci 0000:01:00.0: reg 14: [io  0x6000-0x60ff]
[    0.291279] pci 0000:01:00.0: reg 18: [mem 0xd8100000-0xd810ffff]
[    0.291306] pci 0000:01:00.0: reg 30: [mem 0xfffe0000-0xffffffff pref]
[    0.291325] pci 0000:01:00.0: supports D1 D2
[    0.291345] pci 0000:01:00.1: [1002:aa28] type 0 class 0x000403
[    0.291356] pci 0000:01:00.1: reg 10: [mem 0xd8110000-0xd8113fff]
[    0.291411] pci 0000:01:00.1: supports D1 D2
[    0.296029] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.296033] pci 0000:00:01.0:   bridge window [io  0x6000-0x6fff]
[    0.296036] pci 0000:00:01.0:   bridge window [mem 0xd8100000-0xd81fffff]
[    0.296041] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.296144] pci 0000:02:00.0: [14e4:1713] type 0 class 0x000200
[    0.296168] pci 0000:02:00.0: reg 10: [mem 0xd7100000-0xd710ffff 64bit]
[    0.296269] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.296274] pci 0000:02:00.0: PME# disabled
[    0.304069] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[    0.304073] pci 0000:00:1c.0:   bridge window [io  0x5000-0x5fff]
[    0.304078] pci 0000:00:1c.0:   bridge window [mem 0xd7100000-0xd80fffff]
[    0.304084] pci 0000:00:1c.0:   bridge window [mem 0xd0000000-0xd0ffffff 64bit pref]
[    0.304183] pci 0000:03:00.0: [8086:4237] type 0 class 0x000280
[    0.304220] pci 0000:03:00.0: reg 10: [mem 0xd6100000-0xd6101fff 64bit]
[    0.304359] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[    0.304369] pci 0000:03:00.0: PME# disabled
[    0.312057] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[    0.312062] pci 0000:00:1c.1:   bridge window [io  0x4000-0x4fff]
[    0.312066] pci 0000:00:1c.1:   bridge window [mem 0xd6100000-0xd70fffff]
[    0.312072] pci 0000:00:1c.1:   bridge window [mem 0xd1000000-0xd1ffffff 64bit pref]
[    0.312133] pci 0000:04:00.0: [14e4:4311] type 0 class 0x000280
[    0.312151] pci 0000:04:00.0: reg 10: [mem 0xd5100000-0xd5103fff]
[    0.312250] pci 0000:04:00.0: supports D1 D2
[    0.312271] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.312281] pci 0000:00:1c.2: PCI bridge to [bus 04-04]
[    0.312285] pci 0000:00:1c.2:   bridge window [io  0x3000-0x3fff]
[    0.312289] pci 0000:00:1c.2:   bridge window [mem 0xd5100000-0xd60fffff]
[    0.312296] pci 0000:00:1c.2:   bridge window [mem 0xd2000000-0xd2ffffff 64bit pref]
[    0.312336] pci 0000:00:1c.3: PCI bridge to [bus 05-07]
[    0.312340] pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[    0.312344] pci 0000:00:1c.3:   bridge window [mem 0xd4100000-0xd50fffff]
[    0.312351] pci 0000:00:1c.3:   bridge window [mem 0xd3000000-0xd3ffffff 64bit pref]
[    0.312396] pci 0000:08:09.0: [1180:0832] type 0 class 0x000c00
[    0.312415] pci 0000:08:09.0: reg 10: [mem 0xd4000000-0xd40007ff]
[    0.312481] pci 0000:08:09.0: supports D1 D2
[    0.312483] pci 0000:08:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.312488] pci 0000:08:09.0: PME# disabled
[    0.312508] pci 0000:08:09.1: [1180:0822] type 0 class 0x000805
[    0.312525] pci 0000:08:09.1: reg 10: [mem 0xd4000a00-0xd4000aff]
[    0.312592] pci 0000:08:09.1: supports D1 D2
[    0.312594] pci 0000:08:09.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.312599] pci 0000:08:09.1: PME# disabled
[    0.312617] pci 0000:08:09.2: [1180:0592] type 0 class 0x000880
[    0.312635] pci 0000:08:09.2: reg 10: [mem 0xd4000900-0xd40009ff]
[    0.312701] pci 0000:08:09.2: supports D1 D2
[    0.312703] pci 0000:08:09.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.312707] pci 0000:08:09.2: PME# disabled
[    0.312725] pci 0000:08:09.3: [1180:0852] type 0 class 0x000880
[    0.312742] pci 0000:08:09.3: reg 10: [mem 0xd4000800-0xd40008ff]
[    0.312809] pci 0000:08:09.3: supports D1 D2
[    0.312811] pci 0000:08:09.3: PME# supported from D0 D1 D2 D3hot D3cold
[    0.312815] pci 0000:08:09.3: PME# disabled
[    0.312855] pci 0000:00:1e.0: PCI bridge to [bus 08-08] (subtractive decode)
[    0.312860] pci 0000:00:1e.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.312864] pci 0000:00:1e.0:   bridge window [mem 0xd4000000-0xd40fffff]
[    0.312871] pci 0000:00:1e.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.312874] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.312877] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.312879] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.312882] pci 0000:00:1e.0:   bridge window [mem 0xc0000000-0xfebfffff] (subtractive decode)
[    0.312909] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.313169] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[    0.313238] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[    0.313321] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[    0.313389] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[    0.313458] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
[    0.313526] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
[    0.313602]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.313604] Unable to assume _OSC PCIe control. Disabling ASPM
[    0.320771] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[    0.320839] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[    0.320905] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 *10 11 12)
[    0.320971] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[    0.321036] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12)
[    0.321102] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12)
[    0.321167] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)
[    0.321232] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
[    0.321353] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.321360] vgaarb: loaded
[    0.321402] PCI: Using ACPI for IRQ routing
[    0.321405] PCI: pci_cache_line_size set to 64 bytes
[    0.321631] reserve RAM buffer: 000000000009fc00 - 000000000009ffff 
[    0.321634] reserve RAM buffer: 00000000bdee1000 - 00000000bfffffff 
[    0.321638] reserve RAM buffer: 00000000bfd04000 - 00000000bfffffff 
[    0.321642] reserve RAM buffer: 00000000bfd6a000 - 00000000bfffffff 
[    0.321645] reserve RAM buffer: 00000000bfdeb000 - 00000000bfffffff 
[    0.321648] reserve RAM buffer: 00000000bfe00000 - 00000000bfffffff 
[    0.321755] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[    0.321760] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.321765] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[    0.324040] Switching to clocksource hpet
[    0.325563] pnp: PnP ACPI init
[    0.325576] ACPI: bus type pnp registered
[    0.325981] pnp 00:00: [bus 00-ff]
[    0.325984] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.325987] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.325989] pnp 00:00: [io  0x0600-0x063f]
[    0.325991] pnp 00:00: [io  0x0d00-0xffff window]
[    0.325993] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.325996] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[    0.325998] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[    0.326002] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[    0.326005] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[    0.326007] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[    0.326009] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[    0.326012] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[    0.326014] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[    0.326016] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[    0.326019] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[    0.326021] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[    0.326024] pnp 00:00: [mem 0x000ec000-0x000effff window]
[    0.326026] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[    0.326028] pnp 00:00: [mem 0xc0000000-0xfebfffff window]
[    0.326031] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[    0.326085] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    0.326292] pnp 00:01: [io  0x002e-0x002f]
[    0.326294] pnp 00:01: [io  0x004e-0x004f]
[    0.326297] pnp 00:01: [io  0x164e-0x164f]
[    0.326299] pnp 00:01: [io  0x0068-0x006f]
[    0.326301] pnp 00:01: [io  0x0061]
[    0.326303] pnp 00:01: [io  0x0070]
[    0.326305] pnp 00:01: [io  0x0080]
[    0.326306] pnp 00:01: [io  0x0092]
[    0.326308] pnp 00:01: [io  0x00b2-0x00b3]
[    0.326310] pnp 00:01: [io  0x0063]
[    0.326312] pnp 00:01: [io  0x0065]
[    0.326314] pnp 00:01: [io  0x0067]
[    0.326316] pnp 00:01: [io  0x0600-0x060f]
[    0.326318] pnp 00:01: [io  0x0610]
[    0.326320] pnp 00:01: [io  0x0800-0x080f]
[    0.326322] pnp 00:01: [io  0x0810-0x0817]
[    0.326324] pnp 00:01: [io  0x0820-0x0823]
[    0.326328] pnp 00:01: [io  0x0830-0x083b]
[    0.326330] pnp 00:01: [io  0x0400-0x047f]
[    0.326332] pnp 00:01: [io  0x0500-0x053f]
[    0.326334] pnp 00:01: [mem 0xf8000000-0xfbffffff]
[    0.326336] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[    0.326339] pnp 00:01: [mem 0xfed10000-0xfed13fff]
[    0.326341] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[    0.326343] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[    0.326345] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[    0.326347] pnp 00:01: [mem 0xfed20000-0xfed3ffff]
[    0.326350] pnp 00:01: [mem 0xfed40000-0xfed44fff]
[    0.326352] pnp 00:01: [mem 0xfed45000-0xfed8ffff]
[    0.326354] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[    0.326356] pnp 00:01: [mem 0xff800000-0xff800fff]
[    0.326359] pnp 00:01: [mem 0xff810000-0xff8100ff]
[    0.326475] system 00:01: [io  0x164e-0x164f] has been reserved
[    0.326479] system 00:01: [io  0x0600-0x060f] has been reserved
[    0.326483] system 00:01: [io  0x0610] has been reserved
[    0.326485] system 00:01: [io  0x0800-0x080f] has been reserved
[    0.326489] system 00:01: [io  0x0810-0x0817] has been reserved
[    0.326492] system 00:01: [io  0x0820-0x0823] has been reserved
[    0.326495] system 00:01: [io  0x0830-0x083b] has been reserved
[    0.326499] system 00:01: [io  0x0400-0x047f] has been reserved
[    0.326502] system 00:01: [io  0x0500-0x053f] has been reserved
[    0.326505] system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.326509] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.326512] system 00:01: [mem 0xfed10000-0xfed13fff] has been reserved
[    0.326515] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.326518] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.326521] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.326525] system 00:01: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.326528] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
[    0.326531] system 00:01: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.326534] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.326538] system 00:01: [mem 0xff800000-0xff800fff] has been reserved
[    0.326541] system 00:01: [mem 0xff810000-0xff8100ff] has been reserved
[    0.326544] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.326556] pnp 00:02: [io  0x0000-0x001f]
[    0.326558] pnp 00:02: [io  0x0081-0x0091]
[    0.326560] pnp 00:02: [io  0x0093-0x009f]
[    0.326562] pnp 00:02: [io  0x00c0-0x00df]
[    0.326565] pnp 00:02: [dma 4]
[    0.326598] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.326626] pnp 00:03: [io  0x0070-0x0077]
[    0.326661] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.326741] pnp 00:04: [irq 0 disabled]
[    0.326750] pnp 00:04: [irq 8]
[    0.326752] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[    0.326786] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.326799] pnp 00:05: [io  0x00f0]
[    0.326805] pnp 00:05: [irq 13]
[    0.326839] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.326851] pnp 00:06: [mem 0xffe00000-0xffffffff]
[    0.326887] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[    0.326898] pnp 00:07: [io  0x0060]
[    0.326900] pnp 00:07: [io  0x0064]
[    0.326905] pnp 00:07: [irq 1]
[    0.326940] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.326955] pnp 00:08: [irq 12]
[    0.326994] pnp 00:08: Plug and Play ACPI device, IDs SYN0311 SYN0300 SYN0002 PNP0f13 (active)
[    0.327081] pnp 00:09: [io  0x0620-0x063f]
[    0.327087] pnp 00:09: [irq 4]
[    0.327127] pnp 00:09: Plug and Play ACPI device, IDs WEC1023 (active)
[    0.327182] pnp: PnP ACPI: found 10 devices
[    0.327184] ACPI: ACPI bus type pnp unregistered
[    0.327882] Switched to NOHz mode on CPU #0
[    0.327967] Switched to NOHz mode on CPU #1
[    0.333563] pci 0000:01:00.0: no compatible bridge window for [mem 0xfffe0000-0xffffffff pref]
[    0.333612] pci 0000:01:00.0: BAR 6: assigned [mem 0xd8120000-0xd813ffff pref]
[    0.333615] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.333618] pci 0000:00:01.0:   bridge window [io  0x6000-0x6fff]
[    0.333622] pci 0000:00:01.0:   bridge window [mem 0xd8100000-0xd81fffff]
[    0.333626] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.333631] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[    0.333634] pci 0000:00:1c.0:   bridge window [io  0x5000-0x5fff]
[    0.333639] pci 0000:00:1c.0:   bridge window [mem 0xd7100000-0xd80fffff]
[    0.333643] pci 0000:00:1c.0:   bridge window [mem 0xd0000000-0xd0ffffff 64bit pref]
[    0.333650] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[    0.333653] pci 0000:00:1c.1:   bridge window [io  0x4000-0x4fff]
[    0.333658] pci 0000:00:1c.1:   bridge window [mem 0xd6100000-0xd70fffff]
[    0.333662] pci 0000:00:1c.1:   bridge window [mem 0xd1000000-0xd1ffffff 64bit pref]
[    0.333669] pci 0000:00:1c.2: PCI bridge to [bus 04-04]
[    0.333672] pci 0000:00:1c.2:   bridge window [io  0x3000-0x3fff]
[    0.333677] pci 0000:00:1c.2:   bridge window [mem 0xd5100000-0xd60fffff]
[    0.333681] pci 0000:00:1c.2:   bridge window [mem 0xd2000000-0xd2ffffff 64bit pref]
[    0.333688] pci 0000:00:1c.3: PCI bridge to [bus 05-07]
[    0.333691] pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[    0.333696] pci 0000:00:1c.3:   bridge window [mem 0xd4100000-0xd50fffff]
[    0.333700] pci 0000:00:1c.3:   bridge window [mem 0xd3000000-0xd3ffffff 64bit pref]
[    0.333707] pci 0000:00:1e.0: PCI bridge to [bus 08-08]
[    0.333709] pci 0000:00:1e.0:   bridge window [io  disabled]
[    0.333714] pci 0000:00:1e.0:   bridge window [mem 0xd4000000-0xd40fffff]
[    0.333718] pci 0000:00:1e.0:   bridge window [mem pref disabled]
[    0.333734] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.333738] pci 0000:00:01.0: setting latency timer to 64
[    0.333748] pci 0000:00:1c.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[    0.333752] pci 0000:00:1c.0: setting latency timer to 64
[    0.333761] pci 0000:00:1c.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20
[    0.333766] pci 0000:00:1c.1: setting latency timer to 64
[    0.333776] pci 0000:00:1c.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[    0.333780] pci 0000:00:1c.2: setting latency timer to 64
[    0.333789] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    0.333794] pci 0000:00:1c.3: setting latency timer to 64
[    0.333800] pci 0000:00:1e.0: setting latency timer to 64
[    0.333804] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.333807] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.333809] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.333812] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff]
[    0.333814] pci_bus 0000:01: resource 0 [io  0x6000-0x6fff]
[    0.333817] pci_bus 0000:01: resource 1 [mem 0xd8100000-0xd81fffff]
[    0.333819] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.333822] pci_bus 0000:02: resource 0 [io  0x5000-0x5fff]
[    0.333825] pci_bus 0000:02: resource 1 [mem 0xd7100000-0xd80fffff]
[    0.333827] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xd0ffffff 64bit pref]
[    0.333830] pci_bus 0000:03: resource 0 [io  0x4000-0x4fff]
[    0.333832] pci_bus 0000:03: resource 1 [mem 0xd6100000-0xd70fffff]
[    0.333835] pci_bus 0000:03: resource 2 [mem 0xd1000000-0xd1ffffff 64bit pref]
[    0.333837] pci_bus 0000:04: resource 0 [io  0x3000-0x3fff]
[    0.333840] pci_bus 0000:04: resource 1 [mem 0xd5100000-0xd60fffff]
[    0.333842] pci_bus 0000:04: resource 2 [mem 0xd2000000-0xd2ffffff 64bit pref]
[    0.333845] pci_bus 0000:05: resource 0 [io  0x2000-0x2fff]
[    0.333847] pci_bus 0000:05: resource 1 [mem 0xd4100000-0xd50fffff]
[    0.333850] pci_bus 0000:05: resource 2 [mem 0xd3000000-0xd3ffffff 64bit pref]
[    0.333853] pci_bus 0000:08: resource 1 [mem 0xd4000000-0xd40fffff]
[    0.333855] pci_bus 0000:08: resource 4 [io  0x0000-0x0cf7]
[    0.333857] pci_bus 0000:08: resource 5 [io  0x0d00-0xffff]
[    0.333860] pci_bus 0000:08: resource 6 [mem 0x000a0000-0x000bffff]
[    0.333862] pci_bus 0000:08: resource 7 [mem 0xc0000000-0xfebfffff]
[    0.333927] NET: Registered protocol family 2
[    0.334089] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.335345] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.339705] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.340301] TCP: Hash tables configured (established 524288 bind 65536)
[    0.340304] TCP reno registered
[    0.340319] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.340363] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.340593] NET: Registered protocol family 1
[    1.940011] pci 0000:00:1a.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[    3.540010] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[    3.540133] pci 0000:01:00.0: Boot video device
[    3.540214] PCI: CLS 64 bytes, default 64
[    3.540265] Unpacking initramfs...
[    3.790298] Freeing initrd memory: 9704k freed
[    3.793799] Simple Boot Flag value 0x5 read from CMOS RAM was invalid
[    3.793802] Simple Boot Flag at 0x44 set to 0x1
[    3.794252] audit: initializing netlink socket (disabled)
[    3.794267] type=2000 audit(1323444650.788:1): initialized
[    3.807455] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    3.808134] VFS: Disk quotas dquot_6.5.2
[    3.808170] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    3.808244] msgmni has been set to 6036
[    3.808412] alg: No test for stdrng (krng)
[    3.808444] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    3.808448] io scheduler noop registered
[    3.808450] io scheduler deadline registered
[    3.808470] io scheduler cfq registered (default)
[    3.808582] pcieport 0000:00:01.0: setting latency timer to 64
[    3.808615] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    3.808664] pcieport 0000:00:1c.0: setting latency timer to 64
[    3.808701] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    3.808760] pcieport 0000:00:1c.1: setting latency timer to 64
[    3.808796] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[    3.808853] pcieport 0000:00:1c.2: setting latency timer to 64
[    3.808889] pcieport 0000:00:1c.2: irq 43 for MSI/MSI-X
[    3.808948] pcieport 0000:00:1c.3: setting latency timer to 64
[    3.808983] pcieport 0000:00:1c.3: irq 44 for MSI/MSI-X
[    3.809146] ERST: Table is not found!
[    3.809205] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    3.860494] Linux agpgart interface v0.103
[    3.860754] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    3.873919] i8042: Detected active multiplexing controller, rev 1.1
[    3.882891] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.882898] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    3.882929] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    3.882956] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    3.882982] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    3.883097] mousedev: PS/2 mouse device common for all mice
[    3.883500] rtc_cmos 00:03: RTC can wake from S4
[    3.883612] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    3.883636] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[    3.883649] cpuidle: using governor ladder
[    3.883650] cpuidle: using governor menu
[    3.883879] TCP cubic registered
[    3.883941] NET: Registered protocol family 10
[    3.884532] Mobile IPv6
[    3.884536] NET: Registered protocol family 17
[    3.884540] Registering the dns_resolver key type
[    3.884649] PM: Hibernation image not present or could not be loaded.
[    3.884658] registered taskstats version 1
[    3.885327] rtc_cmos 00:03: setting system clock to 2011-12-09 15:30:51 UTC (1323444651)
[    3.885388] Initializing network drop monitor service
[    3.886919] Freeing unused kernel memory: 596k freed
[    3.887087] Write protecting the kernel read-only data: 6144k
[    3.890411] Freeing unused kernel memory: 764k freed
[    3.893985] Freeing unused kernel memory: 788k freed
[    3.906599] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    3.907074] udev[47]: starting version 164
[    4.044584] usbcore: registered new interface driver usbfs
[    4.044709] usbcore: registered new interface driver hub
[    4.044748] usbcore: registered new device driver usb
[    4.050712] sdhci: Secure Digital Host Controller Interface driver
[    4.050715] sdhci: Copyright(c) Pierre Ossman
[    4.068600] firewire_ohci 0000:08:09.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    4.068607] firewire_ohci 0000:08:09.0: setting latency timer to 64
[    4.069232] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.069260] ehci_hcd 0000:00:1a.7: PCI INT D -> GSI 18 (level, low) -> IRQ 18
[    4.069272] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    4.069275] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    4.069299] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    4.069990] SCSI subsystem initialized
[    4.071958] tg3.c:v3.117 (January 25, 2011)
[    4.072024] tg3 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.072143] tg3 0000:02:00.0: setting latency timer to 64
[    4.088037] ehci_hcd 0000:00:1a.7: debug port 1
[    4.091935] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[    4.091955] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xd8204c00
[    4.094154] libata version 3.00 loaded.
[    4.108015] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    4.108039] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.108042] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.108045] usb usb1: Product: EHCI Host Controller
[    4.108047] usb usb1: Manufacturer: Linux 2.6.39-bpo.2-amd64 ehci_hcd
[    4.108049] usb usb1: SerialNumber: 0000:00:1a.7
[    4.108174] hub 1-0:1.0: USB hub found
[    4.108178] hub 1-0:1.0: 6 ports detected
[    4.108268] ehci_hcd 0000:00:1d.7: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[    4.108285] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    4.108288] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    4.108300] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    4.127353] tg3 0000:02:00.0: eth0: Tigon3 [partno(BCM95906) rev c002] (PCI Express) MAC address 00:1f:16:08:8f:b7
[    4.127357] tg3 0000:02:00.0: eth0: attached PHY is 5906 (10/100Base-TX Ethernet) (WireSpeed[0])
[    4.127361] tg3 0000:02:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[0]
[    4.127364] tg3 0000:02:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    4.165444] firewire_ohci: Added fw-ohci device 0000:08:09.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x1
[    4.165574] sdhci-pci 0000:08:09.1: SDHCI controller found [1180:0822] (rev 22)
[    4.165589] sdhci-pci 0000:08:09.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    4.166601] sdhci-pci 0000:08:09.1: Will use DMA mode even though HW doesn't fully claim to support it.
[    4.166607] sdhci-pci 0000:08:09.1: setting latency timer to 64
[    4.166622] mmc0: no vmmc regulator found
[    4.167646] Registered led device: mmc0::
[    4.168693] mmc0: SDHCI controller on PCI [0000:08:09.1] using DMA
[    4.180044] ehci_hcd 0000:00:1d.7: debug port 1
[    4.183913] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[    4.183921] ehci_hcd 0000:00:1d.7: irq 18, io mem 0xd8204800
[    4.196014] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    4.196051] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    4.196054] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.196056] usb usb2: Product: EHCI Host Controller
[    4.196058] usb usb2: Manufacturer: Linux 2.6.39-bpo.2-amd64 ehci_hcd
[    4.196060] usb usb2: SerialNumber: 0000:00:1d.7
[    4.196173] hub 2-0:1.0: USB hub found
[    4.196177] hub 2-0:1.0: 6 ports detected
[    4.196266] ahci 0000:00:1f.2: version 3.0
[    4.196286] ahci 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[    4.196328] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
[    4.196374] ahci: SSS flag set, parallel bus scan disabled
[    4.196404] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[    4.196408] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part ccc ems 
[    4.196413] ahci 0000:00:1f.2: setting latency timer to 64
[    4.198244] uhci_hcd: USB Universal Host Controller Interface driver
[    4.227185] scsi0 : ahci
[    4.228076] scsi1 : ahci
[    4.228197] scsi2 : ahci
[    4.228298] scsi3 : ahci
[    4.228367] scsi4 : ahci
[    4.228446] scsi5 : ahci
[    4.228730] ata1: SATA max UDMA/133 abar m2048@0xd8204000 port 0xd8204100 irq 45
[    4.228733] ata2: SATA max UDMA/133 abar m2048@0xd8204000 port 0xd8204180 irq 45
[    4.228735] ata3: DUMMY
[    4.228737] ata4: DUMMY
[    4.228739] ata5: SATA max UDMA/133 abar m2048@0xd8204000 port 0xd8204300 irq 45
[    4.228742] ata6: SATA max UDMA/133 abar m2048@0xd8204000 port 0xd8204380 irq 45
[    4.228767] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    4.228775] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    4.228779] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    4.228790] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    4.240033] uhci_hcd 0000:00:1a.0: irq 18, io base 0x000070e0
[    4.240069] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    4.240071] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.240074] usb usb3: Product: UHCI Host Controller
[    4.240076] usb usb3: Manufacturer: Linux 2.6.39-bpo.2-amd64 uhci_hcd
[    4.240078] usb usb3: SerialNumber: 0000:00:1a.0
[    4.240193] hub 3-0:1.0: USB hub found
[    4.240199] hub 3-0:1.0: 2 ports detected
[    4.240272] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    4.240278] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    4.240281] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    4.240292] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    4.252039] uhci_hcd 0000:00:1a.1: irq 19, io base 0x000070c0
[    4.252074] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    4.252077] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.252080] usb usb4: Product: UHCI Host Controller
[    4.252082] usb usb4: Manufacturer: Linux 2.6.39-bpo.2-amd64 uhci_hcd
[    4.252084] usb usb4: SerialNumber: 0000:00:1a.1
[    4.252179] hub 4-0:1.0: USB hub found
[    4.252183] hub 4-0:1.0: 2 ports detected
[    4.252257] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 17 (level, low) -> IRQ 17
[    4.252263] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[    4.252266] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    4.252274] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    4.260040] uhci_hcd 0000:00:1a.2: irq 17, io base 0x000070a0
[    4.260074] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    4.260077] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.260079] usb usb5: Product: UHCI Host Controller
[    4.260081] usb usb5: Manufacturer: Linux 2.6.39-bpo.2-amd64 uhci_hcd
[    4.260083] usb usb5: SerialNumber: 0000:00:1a.2
[    4.260180] hub 5-0:1.0: USB hub found
[    4.260185] hub 5-0:1.0: 2 ports detected
[    4.260253] uhci_hcd 0000:00:1d.0: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[    4.260259] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    4.260262] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    4.260270] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    4.277190] uhci_hcd 0000:00:1d.0: irq 18, io base 0x00007080
[    4.277227] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    4.277230] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.277232] usb usb6: Product: UHCI Host Controller
[    4.277234] usb usb6: Manufacturer: Linux 2.6.39-bpo.2-amd64 uhci_hcd
[    4.277237] usb usb6: SerialNumber: 0000:00:1d.0
[    4.277338] hub 6-0:1.0: USB hub found
[    4.277343] hub 6-0:1.0: 2 ports detected
[    4.277417] uhci_hcd 0000:00:1d.1: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[    4.277423] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    4.277426] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    4.277437] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    4.292039] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00007060
[    4.292077] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    4.292080] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.292083] usb usb7: Product: UHCI Host Controller
[    4.292085] usb usb7: Manufacturer: Linux 2.6.39-bpo.2-amd64 uhci_hcd
[    4.292087] usb usb7: SerialNumber: 0000:00:1d.1
[    4.292222] hub 7-0:1.0: USB hub found
[    4.292227] hub 7-0:1.0: 2 ports detected
[    4.294335] uhci_hcd 0000:00:1d.2: PCI INT D -> GSI 17 (level, low) -> IRQ 17
[    4.294342] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    4.294345] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    4.294355] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    4.301565] thermal LNXTHERM:00: registered as thermal_zone0
[    4.301568] ACPI: Thermal Zone [TZS0] (46 C)
[    4.304044] uhci_hcd 0000:00:1d.2: irq 17, io base 0x00007040
[    4.304083] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    4.304086] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.304088] usb usb8: Product: UHCI Host Controller
[    4.304090] usb usb8: Manufacturer: Linux 2.6.39-bpo.2-amd64 uhci_hcd
[    4.304092] usb usb8: SerialNumber: 0000:00:1d.2
[    4.304203] hub 8-0:1.0: USB hub found
[    4.304207] hub 8-0:1.0: 2 ports detected
[    4.307603] thermal LNXTHERM:01: registered as thermal_zone1
[    4.307606] ACPI: Thermal Zone [TZS1] (46 C)
[    4.424023] usb 1-3: new high speed USB device number 2 using ehci_hcd
[    4.664094] firewire_core: created device fw0: GUID 1234567812345678, S400
[    4.720017] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    4.721078] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    4.721421] ata1.00: ATA-8: Hitachi HTS543232L9A300, FB4OC4DC, max UDMA/133
[    4.721424] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    4.722631] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    4.722974] ata1.00: configured for UDMA/133
[    4.723094] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54323 FB4O PQ: 0 ANSI: 5
[    4.792017] Refined TSC clocksource calibration: 1994.999 MHz.
[    4.792022] Switching to clocksource tsc
[    4.835004] usb 1-3: New USB device found, idVendor=5986, idProduct=0205
[    4.835008] usb 1-3: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[    4.835010] usb 1-3: Product: Lenovo EasyCamera
[    4.835012] usb 1-3: Manufacturer: USB Audio Device
[    5.212012] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    5.213402] ata2.00: ACPI cmd 00/00:00:00:00:00:b0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    5.213406] ata2.00: ATAPI: Optiarc  DVD RW AD-7910S, A801, max UDMA/100
[    5.215025] ata2.00: ACPI cmd 00/00:00:00:00:00:b0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    5.215031] ata2.00: configured for UDMA/100
[    5.217549] scsi 1:0:0:0: CD-ROM            Optiarc  DVD RW AD-7910S  A801 PQ: 0 ANSI: 5
[    5.352011] usb 7-1: new low speed USB device number 2 using uhci_hcd
[    5.506076] usb 7-1: New USB device found, idVendor=04b3, idProduct=3107
[    5.506080] usb 7-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.536015] ata5: SATA link down (SStatus 0 SControl 300)
[    5.856019] ata6: SATA link down (SStatus 0 SControl 300)
[    5.867836] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    5.867890] sd 0:0:0:0: [sda] Write Protect is off
[    5.867893] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    5.867916] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.876750] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    5.876753] cdrom: Uniform CD-ROM driver Revision: 3.20
[    5.876859] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    5.877279] input: HID 04b3:3107 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1:1.0/input/input1
[    5.877361] generic-usb 0003:04B3:3107.0001: input,hidraw0: USB HID v11.10 Mouse [HID 04b3:3107] on usb-0000:00:1d.1-1/input0
[    5.877380] usbcore: registered new interface driver usbhid
[    5.877382] usbhid: USB HID core driver
[    5.934039]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[    5.934429] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.940248] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    5.940311] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    6.624723] PM: Starting manual resume from disk
[    6.624726] PM: Hibernation image partition 8:6 present
[    6.624728] PM: Looking for hibernation image.
[    6.651042] PM: Image not found (code -22)
[    6.651044] PM: Hibernation image not present or could not be loaded.
[    6.707455] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    8.162828] udev[404]: starting version 164
[    8.437587] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[    8.439240] ACPI: Lid Switch [LID0]
[    8.439292] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
[    8.439297] ACPI: Sleep Button [SLPB]
[    8.439365] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[    8.439368] ACPI: Power Button [PWRF]
[    8.449366] wmi: Mapper loaded
[    8.452761] ACPI: acpi_idle registered with cpuidle
[    8.457575] Monitor-Mwait will be used to enter C-1 state
[    8.457872] Monitor-Mwait will be used to enter C-2 state
[    8.459746] Monitor-Mwait will be used to enter C-3 state
[    8.459754] Marking TSC unstable due to TSC halts in idle
[    8.461406] Switching to clocksource hpet
[    8.564525] input: PC Speaker as /devices/platform/pcspkr/input/input5
[    8.622842] lib80211: common routines for IEEE802.11 drivers
[    8.622845] lib80211_crypt: registered algorithm 'NULL'
[    8.628314] acpi device:03: registered as cooling_device2
[    8.628834] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6
[    8.628932] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[    8.705269] r852 0000:08:09.3: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    8.705276] r852 0000:08:09.3: setting latency timer to 64
[    8.705335] r852: driver loaded successfully
[    8.797711] ACPI: AC Adapter [ADP1] (on-line)
[    8.837937] cfg80211: Calling CRDA to update world regulatory domain
[    8.968370] acer_wmi: Acer Laptop ACPI-WMI Extras
[    9.020102] ACPI: Battery Slot [BAT0] (battery present)
[    9.108472] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[    9.119692] input: Ideapad extra buttons as /devices/platform/ideapad/input/input7
[    9.175320] Disabling lock debugging due to kernel taint
[    9.175347] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[    9.294618] [fglrx] Maximum main memory to use for locked dma buffers: 2874 MBytes.
[    9.295109] [fglrx]   vendor: 1002 device: 95c4 count: 1
[    9.295910] [fglrx] ioport: bar 1, base 0x6000, size: 0x100
[    9.295925] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    9.295930] pci 0000:01:00.0: setting latency timer to 64
[    9.296282] [fglrx] Kernel PAT support is enabled
[    9.296302] [fglrx] module loaded - fglrx 8.91.4 [Oct 25 2011] with 1 minors
[    9.545055] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1c0b1, caps: 0xa04711/0xa00000/0x0
[    9.618277] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    9.618657] HDA Intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[    9.618684] HDA Intel 0000:00:1b.0: setting latency timer to 64
[    9.626243] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input8
[    9.693167] Linux media interface: v0.10
[    9.709153] Linux video capture interface: v2.00
[    9.743592] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (5986:0205)
[    9.759366] input: Lenovo EasyCamera as /devices/pci0000:00/0000:00:1a.7/usb1/1-3/1-3:1.0/input/input9
[    9.759428] usbcore: registered new interface driver uvcvideo
[    9.759430] USB Video Class driver (v1.0.0)
[    9.848290] hda_codec: ALC269: BIOS auto-probing.
[    9.849486] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
[    9.851619] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[    9.851690] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[    9.851835] HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    9.851889] HDA Intel 0000:01:00.1: irq 47 for MSI/MSI-X
[    9.851913] HDA Intel 0000:01:00.1: setting latency timer to 64
[   10.175040] wl 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   10.175047] wl 0000:04:00.0: setting latency timer to 64
[   10.177490] wlan%d: 5.100.82.112 driver failed with code 21
[   10.177505] ------------[ cut here ]------------
[   10.177551] kernel BUG at /usr/src/linux-headers-2.6.39-bpo.2-common/include/net/cfg80211.h:1792!
[   10.177598] invalid opcode: 0000 [#1] SMP 
[   10.177719] last sysfs file: /sys/devices/pci0000:00/0000:00:1a.7/usb1/1-3/1-3:1.0/video4linux/video0/uevent
[   10.177767] CPU 0 
[   10.177808] Modules linked in: wl(P+) snd_hda_codec_hdmi snd_hda_codec_realtek joydev uvcvideo videodev media snd_hda_intel snd_hda_codec snd_seq v4l2_compat_ioctl32 snd_seq_device snd_hwdep fglrx(P) snd_pcm snd_timer ideapad_laptop i2c_i801 tpm_tis acer_wmi tpm snd sparse_keymap cfg80211 soundcore battery ac r852 sm_common nand nand_ids nand_ecc psmouse mtd tpm_bios rfkill lib80211 i2c_core video snd_page_alloc serio_raw evdev pcspkr processor power_supply wmi button ext4 mbcache jbd2 crc16 sg sr_mod sd_mod cdrom usbhid crc_t10dif hid uhci_hcd ahci libahci libata sdhci_pci tg3 firewire_ohci ehci_hcd scsi_mod sdhci mmc_core usbcore firewire_core thermal libphy crc_itu_t thermal_sys [last unloaded: scsi_wait_scan]
[   10.180007] 
[   10.180007] Pid: 603, comm: modprobe Tainted: P           O 2.6.39-bpo.2-amd64 #1 LENOVO INVALID/Base Board Product Name
[   10.180007] RIP: 0010:[<ffffffffa07ab312>]  [<ffffffffa07ab312>] wl_cfg80211_detach+0x12/0xd3 [wl]
[   10.180007] RSP: 0018:ffff880037a8dbe8  EFLAGS: 00010246
[   10.180007] RAX: 0000000000000000 RBX: ffff880037692f40 RCX: 0000000000000973
[   10.180007] RDX: 0000000000000000 RSI: ffff880037692f40 RDI: ffff880037692800
[   10.180007] RBP: ffff8800b9394c00 R08: 0000000000000002 R09: 0000000000000005
[   10.180007] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880037692800
[   10.180007] R13: 0000000000000000 R14: ffff8800b93c43c0 R15: 0000000000000012
[   10.180007] FS:  00007fe8b108b700(0000) GS:ffff8800bfa00000(0000) knlGS:0000000000000000
[   10.180007] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   10.180007] CR2: 00007fe8b0b23000 CR3: 00000000b8829000 CR4: 00000000000006f0
[   10.180007] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   10.180007] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[   10.180007] Process modprobe (pid: 603, threadinfo ffff880037a8c000, task ffff880037a36820)
[   10.180007] Stack:
[   10.180007]  0000000000000246 ffff880037692f40 ffff8800b9394c00 ffffffffa07a7ab4
[   10.180007]  312e30312020205b ffff8800b9394c00 ffff8800be8f2000 ffffffffa07a87e2
[   10.180007]  ffff8800b9394c00 ffff8800b93c43c0 ffff880037a8dcd8 00000000ed6911e2
[   10.180007] Call Trace:
[   10.180007]  [<ffffffffa07a7ab4>] ? wl_free_if+0x2a/0x81 [wl]
[   10.180007]  [<ffffffffa07a87e2>] ? wl_free+0x53/0x208 [wl]
[   10.180007]  [<ffffffff81331333>] ? printk+0x40/0x45
[   10.180007]  [<ffffffffa07aea04>] ? wl_pci_probe+0x476/0xa72 [wl]
[   10.180007]  [<ffffffff8124b905>] ? __pm_runtime_set_status+0x162/0x186
[   10.180007]  [<ffffffff811bc07a>] ? local_pci_probe+0x49/0x92
[   10.180007]  [<ffffffff811bcd82>] ? pci_device_probe+0xc2/0xef
[   10.180007]  [<ffffffff81244db8>] ? driver_sysfs_add+0x66/0x8d
[   10.180007]  [<ffffffff81244ef9>] ? driver_probe_device+0xa8/0x138
[   10.180007]  [<ffffffff81244fd8>] ? __driver_attach+0x4f/0x6f
[   10.180007]  [<ffffffff81244f89>] ? driver_probe_device+0x138/0x138
[   10.180007]  [<ffffffff8124457c>] ? bus_for_each_dev+0x44/0x78
[   10.180007]  [<ffffffff812449d4>] ? bus_add_driver+0xa8/0x1f0
[   10.180007]  [<ffffffff81245505>] ? driver_register+0x90/0xf8
[   10.180007]  [<ffffffff811bcfcc>] ? __pci_register_driver+0x4e/0xc0
[   10.180007]  [<ffffffffa094c000>] ? 0xffffffffa094bfff
[   10.180007]  [<ffffffff81002078>] ? do_one_initcall+0x78/0x131
[   10.180007]  [<ffffffff810757ce>] ? sys_init_module+0xd3/0x221
[   10.180007]  [<ffffffff81339392>] ? system_call_fastpath+0x16/0x1b
[   10.180007] Code: e8 48 a3 b1 ff 48 89 df e8 84 19 94 e0 48 c7 45 00 00 00 00 00 5a 5b 5d c3 55 53 48 83 ec 08 48 8b 87 70 02 00 00 48 85 c0 75 04 <0f> 0b eb fe 48 8b 18 48 85 db 75 04 0f 0b eb fe 48 81 c3 20 03 
[   10.180007] RIP  [<ffffffffa07ab312>] wl_cfg80211_detach+0x12/0xd3 [wl]
[   10.180007]  RSP <ffff880037a8dbe8>
[   10.186487] ---[ end trace 33c691bf153e3c24 ]---
[   11.412630] Adding 1951740k swap on /dev/sda6.  Priority:-1 extents:1 across:1951740k 
[   11.415936] EXT4-fs (sda1): re-mounted. Opts: (null)
[   11.826381] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   11.909872] loop: module loaded
[   12.764582] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[   12.810018] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[   13.289772] fuse init (API version 7.16)
[   16.757126] Bluetooth: Core ver 2.16
[   16.757149] NET: Registered protocol family 31
[   16.757151] Bluetooth: HCI device and connection manager initialized
[   16.757153] Bluetooth: HCI socket layer initialized
[   16.757155] Bluetooth: L2CAP socket layer initialized
[   16.757309] Bluetooth: SCO socket layer initialized
[   16.785543] Bluetooth: RFCOMM TTY layer initialized
[   16.785548] Bluetooth: RFCOMM socket layer initialized
[   16.785550] Bluetooth: RFCOMM ver 1.11
[   17.005180] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   17.005185] Bluetooth: BNEP filters: protocol multicast
[   17.048061] Bridge firewalling registered
[   17.323262] lp: driver loaded but no devices found
[   17.338498] ppdev: user-space parallel port driver
[   17.437868] fglrx_pci 0000:01:00.0: irq 48 for MSI/MSI-X
[   17.438630] [fglrx] Firegl kernel thread PID: 1282
[   17.438699] [fglrx] Firegl kernel thread PID: 1283
[   17.438764] [fglrx] Firegl kernel thread PID: 1284
[   17.438894] [fglrx] IRQ 48 Enabled
[   18.882653] [fglrx] Gart USWC size:944 M.
[   18.882657] [fglrx] Gart cacheable size:373 M.
[   18.882662] [fglrx] Reserved FB block: Shared offset:0, size:1000000 
[   18.882666] [fglrx] Reserved FB block: Unshared offset:fd06000, size:2f5000 
[   18.882668] [fglrx] Reserved FB block: Unshared offset:fffb000, size:5000 
[   19.603775] tg3 0000:02:00.0: irq 49 for MSI/MSI-X
[   19.635919] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   21.248236] tg3 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex
[   21.248247] tg3 0000:02:00.0: eth0: Flow control is on for TX and on for RX
[   21.249493] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   50.212305] tg3 0000:02:00.0: irq 49 for MSI/MSI-X
[   50.242586] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   51.855551] tg3 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex
[   51.855563] tg3 0000:02:00.0: eth0: Flow control is on for TX and on for RX
[   51.856839] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

xaos52 · 2011-12-09 15:49:23

[ 10.177490] wlan%d: 5.100.82.112 driver failed with code 21

The %d should be 0 or 1.

Can you remove file

rm /etc/udev/rules.d/70-persistent-net.rules

It will be rebuilt during next boot.

Then reboot.

joksim · 2011-12-09 15:54:02

Still nothing...
No wlan1 in iwconfig...

xaos52 · 2011-12-09 15:56:04

Comment this line in /etc/modprobe.d/broadcom-sta-common.conf

install wl /sbin/modprobe --ignore-install wl $CMDLINE_OPTS

and it will work ( I hope )

joksim · 2011-12-09 16:02:17

Still not working...
Commented the line, run sudo update-initramfs -u
Rebooted, still no wireless in iwconfig

Damn...

nuxero · 2011-12-09 16:02:39

One thig that you can do is open Synaptic Package Manager, then type in the search box "bcm4311" and will appear some packages related to the broadcom cards, then install firmware-b43-installer and reboot. Now you will be able to use your wifi card. Note: you'll need to have the non-free in the debian official repository big_smile

xaos52 · 2011-12-09 16:07:07

Well, I am the end of my latin here.

If someone else wants to chime in, by all means...

Got to go now. Good luck.

joksim · 2011-12-09 16:09:57

Four packages appear and they are all installed...

Package Installed version
firmware-b43-installer 4.150.10.5-4
broadcom-sta-modules-2.6.39-bpo.2-amd64 5.100.82.112-3
broadcom-sta-common 5.100.82.112-3
broadcom-sta-source 5.100.82.112-3+2.6.39-3~bpo60+1

NOTE: I've disabled testing before i run synaptic search

Last edited by joksim (2011-12-09 16:11:01)

joksim · 2011-12-09 16:18:37

Thanks for the help xaos52. I owe you 3 beers at least for the effort smile

Hope I'll resolve this problem, it's a deal breaker for me and #!

Last edited by joksim (2011-12-09 16:19:29)

nuxero · 2011-12-09 16:18:52

Perhaps because of all the stuff you made it before, something is missing, the same happen to me with my bcm4313, i search on the internet and find a very complex solution, so I ignored it (I'm a little lazy to read hehehe). Then I just look up in the Synaptic Package Manager somenthing for my card and I found a package, I installed and everything works fine. Try a reinstallation of #! and then try only the stuff I just told you big_smile

joksim · 2011-12-09 16:32:25

I thought of it too...

I reinstalled #!, but this time I had a wired connection during the install...

Now when I log in, i have both wireless network cards, but I can't enable the wireless...

here is the output form iwconfig:

lo        no wireless extensions.

eth0      no wireless extensions.

wlan1     IEEE 802.11bg  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
          
wlan0     IEEE 802.11abgn  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:off
          
pan0      no wireless extensions.

el_koraco · 2011-12-09 16:41:45

If you didn't have the driver, there would be no iface to see in iwconfig (wlan0 and wlan1 simply wouldn't show up). When you say you can't enable wireless, does that mean the network icon doesn't let you select a network to connect to?

xaos52 · 2011-12-09 16:46:40

Found this:

I have an Acer Aspire TimelineX 4820T, which has the BCM43225 chip (it uses
the same driver as the BCM4311). I had tried downgrading to the older
Broadcom 5.60 driver without success. However Giulio's workaround also works
for me. I need to remove the acer-wmi module or wi-fi just doesn't work,
however it will immediately connect once this module is disabled. So I'm not
sure if this is a separate issue unique to Acer laptops or what?

So, blacklist acer-wmi and try again smile

xaos52 · 2011-12-09 16:50:31

Post output of

lspci -knn

now. See which drivers are loaded.
This IS different from the first posts.

snowpine · 2011-12-09 16:52:21

Your card should be supported out-of-the-box by b43 according to http://www.linuxwireless.org/en/users/D … ed_devices (with wl as an alternative). Probably you just need to tell network-manager to use wlan1 instead of wlan0. I don't know how to do this sad but I do know in wicd you can easily do this from the Preferences screen. smile

joksim · 2011-12-09 16:52:35

output of lspci -knn:

00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
    Subsystem: Lenovo Device [17aa:3a00]
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port [8086:2a41] (rev 07)
    Kernel driver in use: pcieport
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03)
    Subsystem: Lenovo Device [17aa:3a09]
    Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03)
    Subsystem: Lenovo Device [17aa:3a0a]
    Kernel driver in use: uhci_hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03)
    Subsystem: Lenovo Device [17aa:3a0b]
    Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03)
    Subsystem: Lenovo Device [17aa:3a0c]
    Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03)
    Subsystem: Lenovo Device [17aa:3a0d]
    Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03)
    Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03)
    Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03)
    Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 [8086:2946] (rev 03)
    Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03)
    Subsystem: Lenovo Device [17aa:3a14]
    Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03)
    Subsystem: Lenovo Device [17aa:3a15]
    Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03)
    Subsystem: Lenovo Device [17aa:3a16]
    Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03)
    Subsystem: Lenovo Device [17aa:3a17]
    Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93)
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03)
    Subsystem: Lenovo Device [17aa:3a00]
00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03)
    Subsystem: Lenovo Device [17aa:3a1b]
    Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03)
    Subsystem: Lenovo Device [17aa:3a1d]
    Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Mobility Radeon HD 3400 Series [1002:95c4]
    Subsystem: Lenovo Device [17aa:3d9e]
    Kernel driver in use: radeon
01:00.1 Audio device [0403]: ATI Technologies Inc RV620 Audio device [Radeon HD 34xx Series] [1002:aa28]
    Subsystem: Lenovo Device [17aa:3d9f]
    Kernel driver in use: HDA Intel
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express [14e4:1713] (rev 02)
    Subsystem: Lenovo IdeaPad S10e [17aa:3a23]
    Kernel driver in use: tg3
03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237]
    Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211]
    Kernel driver in use: iwlagn
04:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
    Subsystem: Hewlett-Packard Company BCM4311 802.11b/g Wireless LAN Controller [103c:1364]
    Kernel driver in use: b43-pci-bridge
08:09.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (rev 05)
    Subsystem: Lenovo Device [17aa:3d94]
    Kernel driver in use: firewire_ohci
08:09.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 22)
    Subsystem: Lenovo Device [17aa:3d90]
    Kernel driver in use: sdhci-pci
08:09.2 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 12)
    Subsystem: Lenovo Device [17aa:3d92]
08:09.3 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev 12)
    Subsystem: Lenovo Device [17aa:3d91]
    Kernel driver in use: r852

joksim · 2011-12-09 16:53:54

snowpine wrote:

Your card should be supported out-of-the-box by b43 according to http://www.linuxwireless.org/en/users/D … ed_devices (with wl as an alternative). Probably you just need to tell network-manager to use wlan1 instead of wlan0. I don't know how to do this but I do know in wicd you can easily do this from the Preferences screen.

Both of the wireless cards are disabled. I have two options, one for wlan0 and one for wlan1

joksim · 2011-12-09 16:56:47

el_koraco wrote:

If you didn't have the driver, there would be no iface to see in iwconfig (wlan0 and wlan1 simply wouldn't show up). When you say you can't enable wireless, does that mean the network icon doesn't let you select a network to connect to?

Enable wireless on right click menu does not work...

On left click, both wireless network cards (Broadcom and Intel Pro) are disabled, with text: wireless is disabled

xaos52 · 2011-12-09 17:00:32

Lets try without network-manager:

sudo invoke-rc.d network-manager stop
pkill nm-applet

edit /etc/network/interfaces to contain this:

# The loopback network interface
auto lo
iface lo inet loopback

# auto wlan0
iface wlan0 inet dhcp
        wpa-ssid xxxxxxxxx
        wpa-psk yyyyyyyy


auto wlan1
iface wlan1 inet dhcp
        wpa-ssid xxxxxxx
        wpa-psk yyyyyyy

replace xxxxxx with your ssid
yyyyyyy with your keyphrase
then

sudo ifdown wlan1
sudo ifup wlan1

Last edited by xaos52 (2011-12-09 17:01:48)

joksim · 2011-12-09 17:08:16

Hmm,

i kill nm, put the followong code in /etc/network/interfaces

# auto wlan0
iface wlan0 inet dhcp
        wpa-ssid telenet-D5F41
        wpa-psk RpTuPQ43pZJd


auto wlan1
iface wlan1 inet dhcp
        wpa-ssid ETNC
        wpa-psk etncetnc

but when I run sudo ifdown wlan1 I get the following message:
ifdown: interface wlan1 not configured

xaos52 · 2011-12-09 17:12:17

Continue with
sudo ifup wlan1

CrunchBang Linux

SEARCH

#26 2011-12-09 15:18:29

Re: Broadcom wireless not working in statler 2011-12

#27 2011-12-09 15:20:00

Re: Broadcom wireless not working in statler 2011-12

#28 2011-12-09 15:36:13

Re: Broadcom wireless not working in statler 2011-12

#29 2011-12-09 15:40:25

Re: Broadcom wireless not working in statler 2011-12

#30 2011-12-09 15:43:14

Re: Broadcom wireless not working in statler 2011-12

#31 2011-12-09 15:49:23

Re: Broadcom wireless not working in statler 2011-12

#32 2011-12-09 15:54:02

Re: Broadcom wireless not working in statler 2011-12

#33 2011-12-09 15:56:04

Re: Broadcom wireless not working in statler 2011-12

#34 2011-12-09 16:02:17

Re: Broadcom wireless not working in statler 2011-12

#35 2011-12-09 16:02:39

Re: Broadcom wireless not working in statler 2011-12

#36 2011-12-09 16:07:07

Re: Broadcom wireless not working in statler 2011-12

#37 2011-12-09 16:09:57

Re: Broadcom wireless not working in statler 2011-12

#38 2011-12-09 16:18:37

Re: Broadcom wireless not working in statler 2011-12

#39 2011-12-09 16:18:52

Re: Broadcom wireless not working in statler 2011-12

#40 2011-12-09 16:32:25

Re: Broadcom wireless not working in statler 2011-12

#41 2011-12-09 16:41:45

Re: Broadcom wireless not working in statler 2011-12

#42 2011-12-09 16:46:40

Re: Broadcom wireless not working in statler 2011-12

#43 2011-12-09 16:50:31

Re: Broadcom wireless not working in statler 2011-12

#44 2011-12-09 16:52:21

Re: Broadcom wireless not working in statler 2011-12

#45 2011-12-09 16:52:35

Re: Broadcom wireless not working in statler 2011-12

#46 2011-12-09 16:53:54

Re: Broadcom wireless not working in statler 2011-12

#47 2011-12-09 16:56:47

Re: Broadcom wireless not working in statler 2011-12

#48 2011-12-09 17:00:32

Re: Broadcom wireless not working in statler 2011-12

#49 2011-12-09 17:08:16

Re: Broadcom wireless not working in statler 2011-12

#50 2011-12-09 17:12:17

Re: Broadcom wireless not working in statler 2011-12

Board footer