SEARCH

Enter your search query in the box above ^, or use the forum search tool.

You are not logged in.

Pages: 1

#1 2013-01-24 08:26:56

Phillip Bromley
Member
Registered: 2011-03-16
Posts: 38

[Solved] Can't get #! to recognize my SCSI hard drive(s)

I'm currently trying to set up an old desktop that I hacked together from various legacy machines to work the way I want it to.

It currently has three hard drives in it:

  1. 75GB IDE hard drive (probably 5400 RPM)

  2. 16GB Seagate Cheetah SCSI 10000 RPM hard drive

  3. 16GB Seagate Cheetah SCSI 10000 RPM hard drive (another one)

The IDE hard drive is connected by a typical IDE ribbon cable to the IDE controller on the motherboard, and works perfectly. I currently have Windows 98SE (for my retro gaming) dual booting with #! 10 Statler on it.

Here's where it get's tricky...

Both SCSI hard drives are hooked up on one SCSI ribbon cable to an Adaptec 29160 SCSI controller card which is connected to a PCI slot on the motherboard.

When the computer boots up I can hear the hard drives spooling up so I know they're working, but I don't see them in GParted, and basically are as if they are weren't there. Seeing as SCSI drives are a largely antiquated technology, the only things I can find in a search engine are old forum threads and tutorials from the 90's which are largely unhelpful. My searches over the past few days have been for naught.

Here's what I'm aiming for: I want to install #!Crunchbang on one of these SCSI hard drives, OpenBSD on the other, and keep Windows98SE on the IDE drive along with a large data partition to be mounted as the home partition for the #! install.

I'm pretty much in over my head, but I wouldn't have it any other way. tongue

Here's what I've gathered so far:

  • The IDE hard drive's jumpers set it as the master drive

  • The SCSI drives have no jumper (which is supposed to be "cable select" IIRC)

  • The SCSI cable is properly terminated

  • I've tried loading the "scsi_mod", "sg_mod", "sg", and "aic7xxx" kernel modules and refreshing the devices list in GParted to no avail

  • This is going to be way harder than I initially thought

And to get a grasp of the hardware I'm working with, this is a seriously retro machine:

  • Pentium 4 2.0 GH/z (single core!)

  • 512mb RAM (128mb X4)

  • Random old NVidia AGP 8X graphics card

And of course the hard drives themselves are really old too!

Any help would be appriciated! I'm sure I'll be on my own with regard to getting OpenBSD on the second SCSI drive, but I could also use some advice on getting GRUB to boot four different operating systems across three hard drives, which will be my next challenge after I get this working.

Thanks in advance!

EDIT: I solved the problem! It was simply a conflict of the SCSI IDs on the hard drives. Changing the SCSI ID by moving the jumpers fixed the problem.

Last edited by Phillip Bromley (2013-01-25 03:18:00)

Offline

Be excellent to each other!

#2 2013-01-24 08:53:46

xaos52
The Good Doctor
From: Planet of the @s
Registered: 2011-06-24
Posts: 4,602

Re: [Solved] Can't get #! to recognize my SCSI hard drive(s)

Any trace of the scsi drives in the dmesg output?
Post output of

dmesg

for review, if you dont mind.

bootinfoscript - emacs primer - wireless problems- I ♥ #!

Offline

#3 2013-01-24 18:23:54

Phillip Bromley
Member
Registered: 2011-03-16
Posts: 38

Re: [Solved] Can't get #! to recognize my SCSI hard drive(s)

Here's my dmesg output:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-5-686 (Debian 2.6.32-28) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Nov 25 18:43:34 UTC 2010
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable)
[    0.000000]  BIOS-e820: 000000001ffc0000 - 000000001fff8000 (ACPI data)
[    0.000000]  BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000] DMI 2.3 present.
[    0.000000] last_pfn = 0x1ffc0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-DFFFF uncachable
[    0.000000]   E0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FE0000000 write-back
[    0.000000]   1 disabled
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] initial memory mapped : 0 - 01800000
[    0.000000] init_memory_mapping: 0000000000000000-000000001ffc0000
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 001fc00000 page 2M
[    0.000000]  001fc00000 - 001ffc0000 page 4k
[    0.000000] kernel direct mapping tables up to 1ffc0000 @ 7000-d000
[    0.000000] RAMDISK: 1762f000 - 1800fb84
[    0.000000] ACPI: RSDP 000ff980 00014 (v00 AMI   )
[    0.000000] ACPI: RSDT 1fff0000 00030 (v01 GATEWA N0CPP116 20020226 MSFT 00001011)
[    0.000000] ACPI: FACP 1fff1000 00074 (v01 GATEWA N0CPP116 20020226 MSFT 00001011)
[    0.000000] ACPI: DSDT 1ffe0000 03BAA (v01 GATEWA N0CPP116 20011110 MSFT 0100000B)
[    0.000000] ACPI: FACS 1fff8000 00040
[    0.000000] ACPI: APIC 1ffe3baa 0005A (v01 GATEWA N0CPP116 20020226 MSFT 00001011)
[    0.000000] ACPI: SSDT 1ffe3c04 00035 (v01 GATEWA N0CPP116 00000001 MSFT 0100000B)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 511MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 1ffc0000
[    0.000000]   low ram: 0 - 1ffc0000
[    0.000000]   node 0 low ram: 00000000 - 1ffc0000
[    0.000000]   node 0 bootmap 00002000 - 00005ff8
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 001ffc0000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0001000000 - 00014c7bb4]    TEXT DATA BSS ==> [0001000000 - 00014c7bb4]
[    0.000000]   #4 [001762f000 - 001800fb84]          RAMDISK ==> [001762f000 - 001800fb84]
[    0.000000]   #5 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
[    0.000000]   #6 [00014c8000 - 00014ce1b4]              BRK ==> [00014c8000 - 00014ce1b4]
[    0.000000]   #7 [0000007000 - 0000009000]          PGTABLE ==> [0000007000 - 0000009000]
[    0.000000]   #8 [0000002000 - 0000006000]          BOOTMAP ==> [0000002000 - 0000006000]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x0001ffc0
[    0.000000]   HighMem  0x0001ffc0 -> 0x0001ffc0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0001ffc0
[    0.000000] On node 0 totalpages: 130911
[    0.000000] free_area_init_node: node 0, pgdat c13b2720, node_mem_map c14d0000
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3967 pages, LIFO batch:0
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 125920 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 24
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c1c00000 s34296 r0 d23048 u4194304
[    0.000000] pcpu-alloc: s34296 r0 d23048 u4194304 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129887
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=bbe68f36-fd79-41a3-8c3e-6f205ecfec5a ro quiet
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 503640k/524032k available (2500k kernel code, 19640k reserved, 1324k data, 372k init, 0k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xffd56000 - 0xfffff000   (2724 kB)
[    0.000000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.000000]     vmalloc : 0xe07c0000 - 0xff3fe000   ( 492 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdffc0000   ( 511 MB)
[    0.000000]       .init : 0xc13bd000 - 0xc141a000   ( 372 kB)
[    0.000000]       .data : 0xc1271019 - 0xc13bc320   (1324 kB)
[    0.000000]       .text : 0xc1000000 - 0xc1271019   (2500 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:1280
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1994.061 MHz processor.
[    0.008006] Calibrating delay loop (skipped), value calculated using timer frequency.. 3988.12 BogoMIPS (lpj=7976244)
[    0.008035] Security Framework initialized
[    0.008042] SELinux:  Disabled at boot.
[    0.008053] Mount-cache hash table entries: 512
[    0.008233] Initializing cgroup subsys ns
[    0.008239] Initializing cgroup subsys cpuacct
[    0.008246] Initializing cgroup subsys devices
[    0.008250] Initializing cgroup subsys freezer
[    0.008254] Initializing cgroup subsys net_cls
[    0.008294] CPU: Trace cache: 12K uops, L1 D cache: 8K
[    0.008300] CPU: L2 cache: 512K
[    0.008304] CPU: Hyper-Threading is disabled
[    0.008310] mce: CPU supports 4 MCE banks
[    0.008326] CPU0: Thermal monitoring enabled (TM1)
[    0.008343] Performance Events: no PMU driver, software events only.
[    0.008355] Checking 'hlt' instruction... OK.
[    0.024606] SMP alternatives: switching to UP code
[    0.033177] Freeing SMP alternatives: 13k freed
[    0.033194] ACPI: Core revision 20090903
[    0.042294] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.042783] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.082476] CPU0: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
[    0.084001] Brought up 1 CPUs
[    0.084001] Total of 1 processors activated (3988.12 BogoMIPS).
[    0.084001] CPU0 attaching NULL sched-domain.
[    0.084001] devtmpfs: initialized
[    0.084001] regulator: core version 0.5
[    0.084001] NET: Registered protocol family 16
[    0.084001] ACPI: bus type pci registered
[    0.084001] PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=2
[    0.084001] PCI: Using configuration type 1 for base access
[    0.084001] bio: create slab <bio-0> at 0
[    0.084001] ACPI: EC: Look up EC in DSDT
[    0.085324] ACPI: Executed 1 blocks of module-level executable AML code
[    0.091227] ACPI: Interpreter enabled
[    0.091238] ACPI: (supports S0 S1 S3 S4 S5)
[    0.091277] ACPI: Using IOAPIC for interrupt routing
[    0.097271] ACPI: Power Resource [FDDP] (off)
[    0.097318] ACPI: Power Resource [URP1] (off)
[    0.097365] ACPI: Power Resource [LPTP] (off)
[    0.097557] ACPI: No dock devices found.
[    0.098822] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.098887] pci 0000:00:00.0: reg 10 32bit mmio pref: [0xf8000000-0xfbffffff]
[    0.099097] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
[    0.099104] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH4 GPIO
[    0.099158] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
[    0.099229] pci 0000:00:1f.2: reg 20 io port: [0xef80-0xef9f]
[    0.099301] pci 0000:00:1f.3: reg 20 io port: [0xefa0-0xefaf]
[    0.099374] pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
[    0.099383] pci 0000:01:00.0: reg 14 32bit mmio pref: [0xe8000000-0xefffffff]
[    0.099409] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xfe8f0000-0xfe8fffff]
[    0.099486] pci 0000:00:01.0: bridge 32bit mmio: [0xfc800000-0xfe8fffff]
[    0.099493] pci 0000:00:01.0: bridge 32bit mmio pref: [0xe4500000-0xf45fffff]
[    0.099541] pci 0000:02:01.0: reg 10 32bit mmio: [0xfeafc000-0xfeafcfff]
[    0.099594] pci 0000:02:01.0: supports D1 D2
[    0.099598] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.099605] pci 0000:02:01.0: PME# disabled
[    0.099649] pci 0000:02:01.1: reg 10 32bit mmio: [0xfeafd000-0xfeafdfff]
[    0.099702] pci 0000:02:01.1: supports D1 D2
[    0.099706] pci 0000:02:01.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.099712] pci 0000:02:01.1: PME# disabled
[    0.099780] pci 0000:02:0a.0: reg 10 io port: [0xdf00-0xdf3f]
[    0.099835] pci 0000:02:0a.0: supports D1 D2
[    0.099883] pci 0000:02:0b.0: reg 10 32bit mmio: [0xfeafa000-0xfeafafff]
[    0.099936] pci 0000:02:0b.0: supports D1 D2
[    0.099940] pci 0000:02:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.099946] pci 0000:02:0b.0: PME# disabled
[    0.099989] pci 0000:02:0b.1: reg 10 32bit mmio: [0xfeafb000-0xfeafbfff]
[    0.100012] pci 0000:02:0b.1: reg 14 io port: [0xdfa0-0xdfaf]
[    0.100061] pci 0000:02:0b.1: supports D1 D2
[    0.100065] pci 0000:02:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.100072] pci 0000:02:0b.1: PME# disabled
[    0.100130] pci 0000:02:0c.0: reg 10 io port: [0xd800-0xd8ff]
[    0.100146] pci 0000:02:0c.0: reg 14 64bit mmio: [0xfeaff000-0xfeafffff]
[    0.100171] pci 0000:02:0c.0: reg 30 32bit mmio pref: [0xfeac0000-0xfeadffff]
[    0.100255] pci 0000:02:0d.0: reg 10 32bit mmio: [0xfeaa0000-0xfeabffff]
[    0.100266] pci 0000:02:0d.0: reg 14 32bit mmio: [0xfea80000-0xfea9ffff]
[    0.100276] pci 0000:02:0d.0: reg 18 io port: [0xde80-0xdebf]
[    0.100302] pci 0000:02:0d.0: reg 30 32bit mmio pref: [0xfea60000-0xfea7ffff]
[    0.100334] pci 0000:02:0d.0: PME# supported from D0 D3hot D3cold
[    0.100340] pci 0000:02:0d.0: PME# disabled
[    0.100388] pci 0000:00:1e.0: transparent bridge
[    0.100395] pci 0000:00:1e.0: bridge io port: [0xd000-0xdfff]
[    0.100402] pci 0000:00:1e.0: bridge 32bit mmio: [0xfe900000-0xfeafffff]
[    0.100410] pci 0000:00:1e.0: bridge 32bit mmio pref: [0xf4600000-0xf46fffff]
[    0.100425] pci_bus 0000:00: on NUMA node 0
[    0.100432] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.100542] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[    0.112183] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.112336] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    0.112486] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[    0.112636] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    0.112787] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.112939] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 *4 5 6 7 9 10 11 12 14 15)
[    0.113092] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
[    0.113237] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[    0.113400] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.113410] vgaarb: loaded
[    0.113531] PCI: Using ACPI for IRQ routing
[    0.113770] Switching to clocksource tsc
[    0.115833] pnp: PnP ACPI init
[    0.115859] ACPI: bus type pnp registered
[    0.117301] pnp: PnP ACPI: found 10 devices
[    0.117306] ACPI: ACPI bus type pnp unregistered
[    0.117314] PnPBIOS: Disabled by ACPI PNP
[    0.117335] system 00:09: iomem range 0x0-0x9ffff could not be reserved
[    0.117342] system 00:09: iomem range 0xe0000-0xfffff could not be reserved
[    0.117349] system 00:09: iomem range 0x100000-0x1fffffff could not be reserved
[    0.117355] system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.117360] system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.152211] pci 0000:02:0c.0: BAR 6: address space collision on of device [0xfeac0000-0xfeadffff]
[    0.152276] pci 0000:02:0d.0: BAR 6: address space collision on of device [0xfea60000-0xfea7ffff]
[    0.152347] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.152351] pci 0000:00:01.0:   IO window: disabled
[    0.152358] pci 0000:00:01.0:   MEM window: 0xfc800000-0xfe8fffff
[    0.152365] pci 0000:00:01.0:   PREFETCH window: 0xe4500000-0xf45fffff
[    0.152378] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[    0.152384] pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
[    0.152392] pci 0000:00:1e.0:   MEM window: 0xfe900000-0xfeafffff
[    0.152399] pci 0000:00:1e.0:   PREFETCH window: 0xf4600000-0xf46fffff
[    0.152424] pci 0000:00:1e.0: setting latency timer to 64
[    0.152432] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.152437] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.152443] pci_bus 0000:01: resource 1 mem: [0xfc800000-0xfe8fffff]
[    0.152448] pci_bus 0000:01: resource 2 pref mem [0xe4500000-0xf45fffff]
[    0.152453] pci_bus 0000:02: resource 0 io:  [0xd000-0xdfff]
[    0.152458] pci_bus 0000:02: resource 1 mem: [0xfe900000-0xfeafffff]
[    0.152462] pci_bus 0000:02: resource 2 pref mem [0xf4600000-0xf46fffff]
[    0.152467] pci_bus 0000:02: resource 3 io:  [0x00-0xffff]
[    0.152472] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[    0.152526] NET: Registered protocol family 2
[    0.152671] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.153115] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.153217] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.153312] TCP: Hash tables configured (established 16384 bind 16384)
[    0.153316] TCP reno registered
[    0.153423] NET: Registered protocol family 1
[    0.153485] pci 0000:01:00.0: Boot video device
[    0.182265] Unpacking initramfs...
[    0.698194] Freeing initrd memory: 10114k freed
[    0.712933] audit: initializing netlink socket (disabled)
[    0.712958] type=2000 audit(1359026628.710:1): initialized
[    0.717051] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.719322] VFS: Disk quotas dquot_6.5.2
[    0.719414] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.719549] msgmni has been set to 1004
[    0.719852] alg: No test for stdrng (krng)
[    0.719947] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.719952] io scheduler noop registered
[    0.719955] io scheduler anticipatory registered
[    0.719959] io scheduler deadline registered
[    0.720032] io scheduler cfq registered (default)
[    0.720291] isapnp: Scanning for PnP cards...
[    1.074234] isapnp: No Plug & Play device found
[    1.076435] Linux agpgart interface v0.103
[    1.076538] agpgart-intel 0000:00:00.0: Intel i850 Chipset
[    1.080508] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[    1.080614] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.081168] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    1.084366] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.084377] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.084548] mice: PS/2 mouse device common for all mice
[    1.084631] rtc_cmos 00:02: RTC can wake from S4
[    1.084695] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    1.084724] rtc0: alarms up to one month, 114 bytes nvram
[    1.084744] cpuidle: using governor ladder
[    1.084747] cpuidle: using governor menu
[    1.084754] No iBFT detected.
[    1.085369] TCP cubic registered
[    1.085580] NET: Registered protocol family 10
[    1.086324] lo: Disabled Privacy Extensions
[    1.086846] Mobile IPv6
[    1.086851] NET: Registered protocol family 17
[    1.086876] Using IPI No-Shortcut mode
[    1.087001] PM: Resume from disk failed.
[    1.087019] registered taskstats version 1
[    1.087345] rtc_cmos 00:02: setting system clock to 2013-01-24 11:23:50 UTC (1359026630)
[    1.087393] Initalizing network drop monitor service
[    1.087432] Freeing unused kernel memory: 372k freed
[    1.087984] Write protecting the kernel text: 2504k
[    1.088039] Write protecting the kernel read-only data: 920k
[    1.109751] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.120274] udev[46]: starting version 164
[    1.417436] usbcore: registered new interface driver usbfs
[    1.417700] usbcore: registered new interface driver hub
[    1.417969] usbcore: registered new device driver usb
[    1.423712] SCSI subsystem initialized
[    1.436124] Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI
[    1.436131] Copyright (c) 1999-2006 Intel Corporation.
[    1.436192] e1000 0000:02:0d.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[    1.442613] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.451904] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.456969] Floppy drive(s): fd0 is 1.44M
[    1.721573] e1000: 0000:02:0d.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:17:d6:67
[    1.721980] uhci_hcd: USB Universal Host Controller Interface driver
[    1.722082] uhci_hcd 0000:00:1f.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    1.722096] uhci_hcd 0000:00:1f.2: setting latency timer to 64
[    1.722103] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[    1.722148] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[    1.722192] uhci_hcd 0000:00:1f.2: irq 19, io base 0x0000ef80
[    1.722256] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    1.722261] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.722266] usb usb1: Product: UHCI Host Controller
[    1.722269] usb usb1: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[    1.722273] usb usb1: SerialNumber: 0000:00:1f.2
[    1.722559] usb usb1: configuration #1 chosen from 1 choice
[    1.722678] hub 1-0:1.0: USB hub found
[    1.722694] hub 1-0:1.0: 2 ports detected
[    1.727865] FDC 0 is a post-1991 82077
[    1.740223] libata version 3.00 loaded.
[    1.752483] ata_piix 0000:00:1f.1: version 2.13
[    1.752568] ata_piix 0000:00:1f.1: setting latency timer to 64
[    1.752691] scsi0 : ata_piix
[    1.753427] scsi1 : ata_piix
[    1.756103] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    1.756110] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    1.778412] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[    1.778468] ohci_hcd 0000:02:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    1.778501] ohci_hcd 0000:02:01.0: OHCI Host Controller
[    1.778525] ohci_hcd 0000:02:01.0: new USB bus registered, assigned bus number 2
[    1.778551] ohci_hcd 0000:02:01.0: irq 19, io mem 0xfeafc000
[    1.832047] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.832055] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.832060] usb usb2: Product: OHCI Host Controller
[    1.832064] usb usb2: Manufacturer: Linux 2.6.32-5-686 ohci_hcd
[    1.832068] usb usb2: SerialNumber: 0000:02:01.0
[    1.832226] usb usb2: configuration #1 chosen from 1 choice
[    1.832282] hub 2-0:1.0: USB hub found
[    1.832297] hub 2-0:1.0: 3 ports detected
[    1.832412] aic7xxx 0000:02:0c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    2.049056] ata2.00: ATAPI: DVDRW IDE 16X, VER A07F, max UDMA/66
[    2.049114] ata2.01: ATAPI: SAMSUNG CD-R/RW SW-252S, R902, max UDMA/33
[    2.049268] ata1.00: ATA-6: ST380011A, 3.08, max UDMA/100
[    2.049274] ata1.00: 156301488 sectors, multi 16: LBA 
[    2.049313] ata1.00: limited to UDMA/33 due to 40-wire cable
[    2.056318] ata2.00: configured for UDMA/66
[    2.064440] ata1.00: configured for UDMA/33
[    2.064602] scsi 0:0:0:0: Direct-Access     ATA      ST380011A        3.08 PQ: 0 ANSI: 5
[    2.072232] ata2.01: configured for UDMA/33
[    2.073740] scsi 1:0:0:0: CD-ROM            DVDRW    IDE 16X          A07F PQ: 0 ANSI: 5
[    2.074976] scsi 1:0:1:0: CD-ROM            SAMSUNG  CD-R/RW SW-252S  R902 PQ: 0 ANSI: 5
[    2.107812] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    2.107907] sd 0:0:0:0: [sda] Write Protect is off
[    2.107913] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.107952] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.108216]  sda:sr0: scsi3-mmc drive: 1x/48x writer cd/rw xa/form2 cdda tray
[    2.113468] Uniform CD-ROM driver Revision: 3.20
[    2.114039] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.117866] sr1: scsi3-mmc drive: 48x/16x writer cd/rw xa/form2 cdda tray
[    2.118423] sr 1:0:1:0: Attached scsi CD-ROM sr1
[    2.124036]  sda1 sda2 < sda5 sda6 >
[    2.142822] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.165519] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.166272] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    2.166420] sr 1:0:1:0: Attached scsi generic sg2 type 5
[   17.044030] scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[   17.044033]         <Adaptec 29160 Ultra160 SCSI adapter>
[   17.044035]         aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[   17.044037] 
[   17.044856] ohci_hcd 0000:02:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[   17.044896] ohci_hcd 0000:02:01.1: OHCI Host Controller
[   17.044917] ohci_hcd 0000:02:01.1: new USB bus registered, assigned bus number 3
[   17.044955] ohci_hcd 0000:02:01.1: irq 18, io mem 0xfeafd000
[   17.100061] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[   17.100070] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   17.100075] usb usb3: Product: OHCI Host Controller
[   17.100079] usb usb3: Manufacturer: Linux 2.6.32-5-686 ohci_hcd
[   17.100083] usb usb3: SerialNumber: 0000:02:01.1
[   17.100248] usb usb3: configuration #1 chosen from 1 choice
[   17.100304] hub 3-0:1.0: USB hub found
[   17.100320] hub 3-0:1.0: 2 ports detected
[   17.476025] usb 3-2: new full speed USB device using ohci_hcd and address 2
[   17.495007] EXT4-fs (sda6): mounted filesystem with ordered data mode
[   17.692017] usb 3-2: New USB device found, idVendor=058f, idProduct=9360
[   17.692024] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   17.692029] usb 3-2: Product: USB Reader
[   17.692033] usb 3-2: Manufacturer:  
[   17.692037] usb 3-2: SerialNumber: 9205291
[   17.692196] usb 3-2: configuration #1 chosen from 1 choice
[   18.759488] udev[253]: starting version 164
[   19.277751] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[   19.277770] ACPI: Power Button [PBTN]
[   19.277898] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[   19.277906] ACPI: Power Button [PWRF]
[   19.472902] processor LNXCPU:00: registered as cooling_device0
[   19.490471] input: PC Speaker as /devices/platform/pcspkr/input/input3
[   19.515086] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   19.559161] intel_rng: Firmware space is locked read-only. If you can't or
[   19.559165] intel_rng: don't want to disable this in firmware setup, and if
[   19.559168] intel_rng: you are certain that your system has a functional
[   19.559170] intel_rng: RNG, try using the 'no_fwh_detect' option.
[   19.571547] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   19.614874] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   19.676147] Initializing USB Mass Storage driver...
[   19.676288] scsi3 : SCSI emulation for USB Mass Storage devices
[   19.676521] usbcore: registered new interface driver usb-storage
[   19.676527] USB Mass Storage support registered.
[   19.677827] usb-storage: device found at 2
[   19.677832] usb-storage: waiting for device to settle before scanning
[   20.084441] [drm] Initialized drm 1.1.0 20060810
[   20.412146] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   20.418571] [drm] nouveau 0000:01:00.0: Detected an NV10 generation card (0x011000b2)
[   20.418672] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PROM
[   20.556851] [drm] nouveau 0000:01:00.0: ... appears to be valid
[   20.557101] [drm] nouveau 0000:01:00.0: BMP BIOS found
[   20.557105] [drm] nouveau 0000:01:00.0: BMP version 5.20
[   20.557111] [drm] nouveau 0000:01:00.0: Bios version 03.11.01.30
[   20.557115] [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 1.5
[   20.557122] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: f0003f00 000088b8
[   20.557127] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: f2045004 0000ffff
[   20.557132] [drm] nouveau 0000:01:00.0: Raw DCB entry 3: f2204f01 ffffffff
[   20.557137] [drm] nouveau 0000:01:00.0: Raw DCB entry 4: f2244f01 ffffffff
[   20.557349] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xAB70
[   20.557368] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xB25E
[   20.557377] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xAB8B
[   20.557399] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xB205
[   20.557412] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xAC1E
[   20.557417] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 5 at offset 0xAD72
[   20.557442] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 6 at offset 0xAC43
[   20.557476] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 7 at offset 0xAD0D
[   20.592966] [TTM] Zone  kernel: Available graphics memory: 257252 kiB.
[   20.592984] [drm] nouveau 0000:01:00.0: 64 MiB VRAM
[   20.593081] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
[   20.593102] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[   20.593126] nouveau 0000:01:00.0: putting AGP V2 device into 4x mode
[   20.593363] [drm] nouveau 0000:01:00.0: 64 MiB GART (aperture)
[   20.593689] [drm] nouveau 0000:01:00.0: Allocating FIFO number 0
[   20.594238] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised FIFO 0
[   20.594413] [drm] nouveau 0000:01:00.0: Initial CRTC_OWNER is 0
[   20.594428] [drm] nouveau 0000:01:00.0: Saving VGA fonts
[   20.647322] [drm] nouveau 0000:01:00.0: Probing TV encoders on I2C bus: 1
[   20.651443] [drm] nouveau 0000:01:00.0: No TV encoders found.
[   20.651450] [drm] nouveau 0000:01:00.0: Probing TV encoders on I2C bus: 1
[   20.655316] [drm] nouveau 0000:01:00.0: No TV encoders found.
[   20.655324] [drm] nouveau 0000:01:00.0: Detected a VGA connector
[   20.655483] [drm] nouveau 0000:01:00.0: Detected a DVI-I connector
[   20.656909] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
[   20.656915] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on tmds encoder (output 1)
[   20.656921] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga encoder (output 2)
[   20.780942] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[   20.826460] [drm] nouveau 0000:01:00.0: Load detected on head A
[   20.828832] [drm] nouveau 0000:01:00.0: allocated 1024x768 fb: 0x49000, bo deaf1e00
[   20.840835] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on vga encoder (output 0)
[   20.840842] [drm] nouveau 0000:01:00.0: Output VGA-1 is running on CRTC 0 using output A
[   20.853525] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on vga encoder (output 2)
[   20.853532] [drm] nouveau 0000:01:00.0: Output DVI-I-1 is running on CRTC 1 using output @
[   20.855994] Console: switching to colour frame buffer device 128x48
[   20.858411] fb0: nouveaufb frame buffer device
[   20.858414] registered panic notifier
[   20.858424] [drm] Initialized nouveau 0.0.15 20090420 for 0000:01:00.0 on minor 0
[   21.123156] ENS1371 0000:02:0a.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   22.679225] Adding 976888k swap on /dev/sda5.  Priority:-1 extents:1 across:976888k 
[   23.105918] loop: module loaded
[   23.661880] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[   24.344488] fuse init (API version 7.13)
[   24.684031] usb-storage: device scan complete
[   24.689741] scsi 3:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
[   24.696733] scsi 3:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
[   24.703726] scsi 3:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
[   24.710730] scsi 3:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
[   26.610850] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   28.729765] Bluetooth: Core ver 2.15
[   28.729878] NET: Registered protocol family 31
[   28.729881] Bluetooth: HCI device and connection manager initialized
[   28.729887] Bluetooth: HCI socket layer initialized
[   28.760679] Bluetooth: L2CAP ver 2.14
[   28.760684] Bluetooth: L2CAP socket layer initialized
[   28.874240] Bluetooth: RFCOMM TTY layer initialized
[   28.874250] Bluetooth: RFCOMM socket layer initialized
[   28.874253] Bluetooth: RFCOMM ver 1.11
[   28.874719] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   28.874724] Bluetooth: BNEP filters: protocol multicast
[   28.939193] Bridge firewalling registered
[   29.183492] [drm] nouveau 0000:01:00.0: Load detected on head A
[   29.308401] Bluetooth: SCO (Voice Link) ver 0.6
[   29.308407] Bluetooth: SCO socket layer initialized
[   29.319601] [drm] nouveau 0000:01:00.0: Load detected on head A
[   29.354431] [drm] nouveau 0000:01:00.0: Allocating FIFO number 1
[   29.354841] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised FIFO 1
[   39.816034] scsi 2:0:6:0: Attempting to queue an ABORT message
[   39.816042] CDB: 0x12 0x0 0x0 0x0 0x24 0x0
[   39.816067] scsi2: At time of recovery, card was not paused
[   39.816079] >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
[   39.816084] scsi2: Dumping Card State in Message-in phase, at SEQADDR 0x42
[   39.816090] Card was paused
[   39.816099] ACCUM = 0x4, SINDEX = 0x67, DINDEX = 0x27, ARG_2 = 0x0
[   39.816107] HCNT = 0x0 SCBPTR = 0x0
[   39.816112] SCSIPHASE[0x0] SCSISIGI[0xa4]:(BSYI|MSGI|CDI) 
[   39.816125] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0xe0]:(MSGI|IOI|CDI) 
[   39.816139] SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) 
[   39.816147] SBLKCTL[0xa]:(SELWIDE|SELBUSB) SCSIRATE[0x0] 
[   39.816157] SEQCTL[0x10]:(FASTMODE) SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) 
[   39.816169] SSTAT0[0x5]:(DMADONE|SDONE) SSTAT1[0x0] 
[   39.816179] SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8]:(ENSWRAP) 
[   39.816191] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) 
[   39.816200] SXFRCTL0[0x80]:(DFON) DFCNTRL[0x4]:(DIRECTION) 
[   39.816211] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) 
[   39.816218] STACK: 0x0 0x0 0x179 0x112
[   39.816234] SCB count = 4
[   39.816238] Kernel NEXTQSCB = 2
[   39.816243] Card NEXTQSCB = 2
[   39.816246] QINFIFO entries: 
[   39.816250] Waiting Queue entries: 
[   39.816256] Disconnected Queue entries: 0:3 
[   39.816265] QOUTFIFO entries: 
[   39.816269] Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 
[   39.816337] Sequencer SCB Info: 
[   39.816342]   0 SCB_CONTROL[0x44]:(DISCONNECTED|DISCENB) 
[   39.816352] SCB_SCSIID[0x67] SCB_LUN[0x0] SCB_TAG[0x3] 
[   39.816362]   1 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816376] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816385]   2 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816399] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816408]   3 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816422] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816431]   4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816445] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816453]   5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816467] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816476]   6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816490] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816499]   7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816512] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816521]   8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816535] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816544]   9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816558] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816566]  10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816580] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816589]  11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816603] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816612]  12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816625] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816634]  13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816648] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816657]  14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816671] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816679]  15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816693] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816702]  16 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816716] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816724]  17 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816738] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816747]  18 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816761] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816769]  19 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816783] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816792]  20 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816806] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816814]  21 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816828] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816837]  22 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816851] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816860]  23 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816873] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816882]  24 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816896] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816905]  25 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816918] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816927]  26 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816941] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816950]  27 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816964] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816972]  28 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.816986] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.816995]  29 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.817009] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.817017]  30 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.817031] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.817040]  31 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   39.817054] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   39.817063] Pending list: 
[   39.817067]   3 SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0x67] 
[   39.817076] SCB_LUN[0x0] 
[   39.817080] Kernel Free SCB list: 1 0 
[   39.817087] Untagged Q(6): 3 
[   39.817092] 
[   39.817094] <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
[   39.817111] scsi 2:0:6:0: Device is active, asserting ATN
[   39.817117] Recovery code sleeping
[   44.816124] Timer Expired
[   44.816130] Recovery code awake
[   44.816134] aic7xxx_abort returns 0x2003
[   44.816146] scsi 2:0:6:0: Attempting to queue a TARGET RESET message
[   44.816150] CDB: 0x12 0x0 0x0 0x0 0x24 0x0
[   44.816162] aic7xxx_dev_reset returns 0x2003
[   44.816284] Recovery SCB completes
[   48.139538] [drm] nouveau 0000:01:00.0: Load detected on head A
[   48.271567] [drm] nouveau 0000:01:00.0: Load detected on head A
[   64.820023] scsi 2:0:6:0: Attempting to queue an ABORT message
[   64.820031] CDB: 0x0 0x0 0x0 0x0 0x0 0x0
[   64.820058] scsi2: At time of recovery, card was not paused
[   64.820071] >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
[   64.820074] scsi2: Dumping Card State in Message-in phase, at SEQADDR 0x42
[   64.820078] Card was paused
[   64.820086] ACCUM = 0x4, SINDEX = 0x67, DINDEX = 0x27, ARG_2 = 0x0
[   64.820092] HCNT = 0x0 SCBPTR = 0x0
[   64.820097] SCSIPHASE[0x0] SCSISIGI[0xa4]:(BSYI|MSGI|CDI) 
[   64.820110] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0xe0]:(MSGI|IOI|CDI) 
[   64.820124] SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) 
[   64.820132] SBLKCTL[0xa]:(SELWIDE|SELBUSB) SCSIRATE[0x0] 
[   64.820142] SEQCTL[0x10]:(FASTMODE) SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) 
[   64.820154] SSTAT0[0x5]:(DMADONE|SDONE) SSTAT1[0x0] 
[   64.820164] SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8]:(ENSWRAP) 
[   64.820176] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) 
[   64.820184] SXFRCTL0[0x80]:(DFON) DFCNTRL[0x4]:(DIRECTION) 
[   64.820195] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) 
[   64.820202] STACK: 0x0 0x0 0x179 0x112
[   64.820218] SCB count = 4
[   64.820222] Kernel NEXTQSCB = 3
[   64.820226] Card NEXTQSCB = 3
[   64.820229] QINFIFO entries: 
[   64.820234] Waiting Queue entries: 
[   64.820239] Disconnected Queue entries: 0:2 
[   64.820249] QOUTFIFO entries: 
[   64.820253] Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 
[   64.820321] Sequencer SCB Info: 
[   64.820326]   0 SCB_CONTROL[0x44]:(DISCONNECTED|DISCENB) 
[   64.820336] SCB_SCSIID[0x67] SCB_LUN[0x0] SCB_TAG[0x2] 
[   64.820346]   1 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820360] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820370]   2 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820384] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820393]   3 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820407] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820416]   4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820430] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820439]   5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820453] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820462]   6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820476] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820485]   7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820500] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820508]   8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820523] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820532]   9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820546] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820555]  10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820569] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820578]  11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820592] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820601]  12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820615] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820624]  13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820638] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820647]  14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820661] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820670]  15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820684] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820693]  16 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820707] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820716]  17 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820731] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820739]  18 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820754] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820763]  19 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820777] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820786]  20 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820800] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820809]  21 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820823] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820832]  22 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820846] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820855]  23 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820869] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820878]  24 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820892] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820901]  25 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820915] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820924]  26 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820938] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820947]  27 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820961] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820970]  28 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.820984] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.820993]  29 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.821007] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.821016]  30 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.821031] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.821039]  31 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) 
[   64.821054] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 
[   64.821063] Pending list: 
[   64.821067]   2 SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0x67] 
[   64.821076] SCB_LUN[0x0] 
[   64.821080] Kernel Free SCB list: 1 0 
[   64.821087] Untagged Q(6): 2 
[   64.821093] 
[   64.821095] <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
[   64.821112] scsi 2:0:6:0: Device is active, asserting ATN
[   64.821119] Recovery code sleeping
[   69.820017] Timer Expired
[   69.820024] Recovery code awake
[   69.820029] aic7xxx_abort returns 0x2003
[   69.820036] scsi 2:0:6:0: Attempting to queue a TARGET RESET message
[   69.820042] CDB: 0x0 0x0 0x0 0x0 0x0 0x0
[   69.820055] aic7xxx_dev_reset returns 0x2003
[   69.820175] Recovery SCB completes
[   79.824022] scsi 2:0:6:0: Device offlined - not ready after error recovery
[   81.875581] sd 3:0:0:0: Attached scsi generic sg3 type 0
[   81.875802] sd 3:0:0:1: Attached scsi generic sg4 type 0
[   81.876042] sd 3:0:0:2: Attached scsi generic sg5 type 0
[   81.876272] sd 3:0:0:3: Attached scsi generic sg6 type 0
[   82.367228] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   82.389217] sd 3:0:0:1: [sdc] Attached SCSI removable disk
[   82.400217] sd 3:0:0:2: [sdd] Attached SCSI removable disk
[   82.411214] sd 3:0:0:3: [sde] Attached SCSI removable disk

It seems to list 4 different SCSI drives, but there's only two in there?

Offline

#4 2013-01-24 19:45:27

xaos52
The Good Doctor
From: Planet of the @s
Registered: 2011-06-24
Posts: 4,602

Re: [Solved] Can't get #! to recognize my SCSI hard drive(s)

If I am reading this correctly, the last 4 lines are for your card reader(s):

[   82.367228] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   82.389217] sd 3:0:0:1: [sdc] Attached SCSI removable disk
[   82.400217] sd 3:0:0:2: [sdd] Attached SCSI removable disk
[   82.411214] sd 3:0:0:3: [sde] Attached SCSI removable disk

corresponding to 

[   24.689741] scsi 3:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
[   24.696733] scsi 3:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
[   24.703726] scsi 3:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
[   24.710730] scsi 3:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0

The adaptec is recognized:

[   17.044030] scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[   17.044033]         <Adaptec 29160 Ultra160 SCSI adapter>
[   17.044035]         aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[   17.044037]

but offlined after 2 recovery attempts.

I suspect that either the Adaptec controller or one/both the devices attached to it is not connected properly.

hth

bootinfoscript - emacs primer - wireless problems- I ♥ #!

Offline

#5 2013-01-24 21:39:24

Phillip Bromley
Member
Registered: 2011-03-16
Posts: 38

Re: [Solved] Can't get #! to recognize my SCSI hard drive(s)

I do indeed have a card reader, so that explains that.

I'm not certain how to tell if I have the drives connected properly. I mean, I have both drives on the ribbon cable, and one of the drinves is connected from the end of the cable (thus properly terminating the cable). The ribbon cable is then firmly connected to the internal SCSI port on the controller card, which is firmly connected to the PCI slot on the motherboard.

It's a 64 bit PCI card, but it's supposed to be backward compatable with a 32 bit PCI slot, albiet with somewhat slower speed, so it should work. I'll double check my connections and see what I find.

Could it also be my jumper settings? If I interpreted the sticker on the drives correctly, no jumper should be the "cable select" mode. Is that correct? Or is there no "cable select" for SCSI drives and I misinterpreted it?

Offline

#6 2013-01-24 23:04:56

bigbenaugust
#! Junkie
From: the 919
Registered: 2009-03-04
Posts: 341

Re: [Solved] Can't get #! to recognize my SCSI hard drive(s)

Is it not the SCSI ID on the drives that is more important than the cable order?

--Ben
Debian: II   Arch: II   openSUSE: I

Offline

#7 2013-01-25 01:14:57

Phillip Bromley
Member
Registered: 2011-03-16
Posts: 38

Re: [Solved] Can't get #! to recognize my SCSI hard drive(s)

Ok, so I went into the Adaptec "SCSISelect" utility (the SCSI BIOS, essentially) and noticed that it only detected the controller card itself (SCSI ID was 7 as is typical), and not the hard drives. I double checked the connections. The hard drives are properly connected to the cable, which is properly connected to the controller card, which is properly connected to the motherboard. I also inspected the cable itself for any damage, there was no damage neither to the wires themselves nor the pins on the connectors. And yet, when the SCSISelect utility scans for SCSI devices, it doesn't find anything assigned SCSI ID 1-5, times out scannng ID 6 (one of the hard drives?), finds the controller card itself assigned to ID 7, and times out searching every SCSI ID after that, all the way to 15.

I am out of ideas. I doubt the hard drives themselves are faulty, because the computers I salvaged them from didn't have hard drive issues. I could try a different cable, but it was working with the computer I took it from too. I tried the other internal SCSI port on the controller card, which didn't work either. I know the hard drives are turning on, because I hear them spool up when I turn on the computer.

I'm still reading the various Adaptec documentation, which is greatfully vast (linux is officially supported) and I may find answers there.

Any other ideas?

EDIT: I just tried disconnecting one of the drives, and upon scanning for SCSI drives in the SCSISelect utility, it detected it! I'm formatting it now, since I'm going to install another OS on it anyways, but then I'll connect just the other one and see if it works too. If so, then it could be a conflicting SCSI ID? This is my first experience with SCSI drives, so I'm not sure. If not, then it's obviously faulty. Eventually I'll get around to seeing if it's detected in Linux, and will let me install to it.

EDIT: Ok, so both hard drives will work individually, but not both together. Either one works perfectly! I noticed that whichever one was connected, it was assigned the SCSI ID of 6. That led me to believe it was an SCSI ID conflict, which explains everything.

So now, my problem is, how do I move the jumpers to reassign the SCSI ID? They are Seagate Cheetah ST318406LW 17 GB 10000 RPM hard drives. This is an older model which is no longer listed on Seagate's website, not even in their support section. I've tried searching for documentation on the internet, but no luck so far. I'll maybe call Seagate tomorrow, but I doubt they'll help.

Would it hurt the drive to randomly move the jumpers to try and change the ID? I don't think I'd fry it by using an incorrect jumper setting.

EDIT: Fixed! I just randomly moved the jumpers until I changed it to the SCSI ID I wanted, with the controller card being ID 7, and the hard drives being IDs 6 and 5. It worked! Thanks for all your help!

Last edited by Phillip Bromley (2013-01-25 03:16:51)

Offline

#8 2013-01-25 23:31:06

bigbenaugust
#! Junkie
From: the 919
Registered: 2009-03-04
Posts: 341

Re: [Solved] Can't get #! to recognize my SCSI hard drive(s)

It's all about the IDs or the termination. Enjoy your old-school storage. smile

Last edited by bigbenaugust (2013-01-25 23:31:20)

--Ben
Debian: II   Arch: II   openSUSE: I

Offline

Pages: 1

Board footer

Powered by FluxBB

Copyright © 2012 CrunchBang Linux.
Proudly powered by Debian. Hosted by Linode.
Debian is a registered trademark of Software in the Public Interest, Inc.

Debian Logo