SEARCH

Enter your search query in the box above ^, or use the forum search tool.

You are not logged in.

#1 2013-03-28 23:56:36

cyrixblack
Member
Registered: 2013-03-13
Posts: 21

Strange wifi behavior

I've got a fresh install and my belkin wifi card is behaving weird:

If I'm in the same room as my wireless access point I get 72% signal strength and 1meg throughput maximum, yet moving to another room it's still +60% and showing up on the nm-applet but just won't connect and pops up with the input password over and over.

If I go back into the room with the access point it connects and does not drop but is only at 1meg max.

I get 9meg throughput on mine and my wife's iPhones across the entire house so it's not my wireless point at fault.

Is it a setting somewhere keeping my wifi card in a low power useage mode?

Offline

Help fund CrunchBang, donate to the project!

#2 2013-03-29 08:46:17

cyrixblack
Member
Registered: 2013-03-13
Posts: 21

Re: Strange wifi behavior

Ive also observed that the nm-applet is not updating very often, I have to wait for a min or so before my wifi pops up.

Offline

#3 2013-03-29 08:52:10

cyrixblack
Member
Registered: 2013-03-13
Posts: 21

Re: Strange wifi behavior

lspci

00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI RS100 AGP Bridge [IGP 320M] (rev 13)
00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI PCI Bridge [IGP 320M] (rev 01)
00:02.0 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
00:06.0 Multimedia audio controller: ULi Electronics Inc. M5451 PCI AC-Link Controller Audio Device (rev 02)
00:07.0 ISA bridge: ULi Electronics Inc. M1533/M1535/M1543 PCI to ISA Bridge [Aladdin IV/V/V+]
00:08.0 Modem: ULi Electronics Inc. M5457 AC'97 Modem Controller
00:0a.0 CardBus bridge: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus Controller
00:10.0 IDE interface: ULi Electronics Inc. M5229 IDE (rev c4)
00:11.0 Bridge: ULi Electronics Inc. M7101 Power Management Controller [PMU]
00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS100 [Radeon IGP320M]
02:00.0 Network controller: Ralink corp. RT2600 802.11 MIMO

Offline

#4 2013-03-29 08:53:19

cyrixblack
Member
Registered: 2013-03-13
Posts: 21

Re: Strange wifi behavior

lsmod

Module                  Size  Used by
fuse                   51989  3 
cpufreq_userspace      12520  0 
cpufreq_powersave      12422  0 
cpufreq_stats          12645  0 
cpufreq_conservative    12987  0 
ext2                   49804  1 
loop                   17851  0 
arc4                   12418  2 
rt61pci                22478  0 
rt2x00pci              12768  1 rt61pci
rt2x00lib              29197  2 rt2x00pci,rt61pci
eeprom_93cx6           12457  1 rt61pci
mac80211              167584  2 rt2x00lib,rt2x00pci
cfg80211              117695  2 mac80211,rt2x00lib
joydev                 12959  0 
rfkill                 18715  2 cfg80211
radeon                567040  2 
crc_itu_t              12331  1 rt61pci
snd_ali5451            18266  2 
snd_ac97_codec         84280  1 snd_ali5451
ttm                    42957  1 radeon
drm_kms_helper         22699  1 radeon
snd_pcm                53481  2 snd_ac97_codec,snd_ali5451
drm                   130145  4 drm_kms_helper,ttm,radeon
snd_page_alloc         12867  1 snd_pcm
i2c_ali15x3            12490  0 
psmouse                59829  0 
i2c_ali1535            12490  0 
i2c_algo_bit           12713  1 radeon
powernow_k7            12745  0 
pcmcia                 32047  0 
snd_seq                39789  0 
snd_seq_device         13016  1 snd_seq
snd_timer              22478  2 snd_seq,snd_pcm
snd                    38827  10 snd_timer,snd_seq_device,snd_seq,snd_pcm,snd_ac97_codec,snd_ali5451
alim1535_wdt           12582  0 
pcspkr                 12554  0 
evdev                  13175  5 
serio_raw              12848  0 
i2c_core               19116  6 i2c_algo_bit,i2c_ali1535,i2c_ali15x3,drm,drm_kms_helper,radeon
soundcore              12921  1 snd
ac97_bus               12462  1 snd_ac97_codec
yenta_socket           22402  0 
parport_pc             22036  0 
pcmcia_rsrc            17380  1 yenta_socket
pcmcia_core            18063  3 pcmcia_rsrc,yenta_socket,pcmcia
parport                31375  1 parport_pc
container              12525  0 
shpchp                 26717  0 
video                  17459  0 
battery                12957  0 
ac                     12552  0 
button                 12817  0 
processor              23136  2 powernow_k7
ext4                  298201  1 
crc16                  12327  1 ext4
jbd2                   51584  1 ext4
mbcache                12938  2 ext4,ext2
cryptd                 14125  0 
aes_i586               16647  3 
aes_generic            32970  1 aes_i586
xts                    12557  1 
gf128mul               12922  1 xts
dm_crypt               17920  1 
dm_mod                 57438  9 dm_crypt
microcode              13198  0 
sg                     21589  0 
sd_mod                 35425  3 
sr_mod                 17468  0 
crc_t10dif             12332  1 sd_mod
cdrom                  34813  1 sr_mod
ata_generic            12439  0 
pata_ali               12880  2 
libata                121252  2 pata_ali,ata_generic
scsi_mod              135542  4 libata,sr_mod,sd_mod,sg
ohci_hcd               22264  0 
ehci_hcd               35684  0 
usbcore               100644  3 ehci_hcd,ohci_hcd
thermal                13103  0 
thermal_sys            17752  3 thermal,processor,video
natsemi                22596  0 
usb_common             12338  1 usbcore

Offline

#5 2013-03-29 08:55:46

cyrixblack
Member
Registered: 2013-03-13
Posts: 21

Re: Strange wifi behavior

dmesg

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.2.0-4-486 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 Debian 3.2.35-2
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000002bef0000 (usable)
[    0.000000]  BIOS-e820: 000000002bef0000 - 000000002beff000 (ACPI data)
[    0.000000]  BIOS-e820: 000000002beff000 - 000000002bf00000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000002bf00000 - 000000002c000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
[    0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[    0.000000] DMI 2.3 present.
[    0.000000] DMI: Hewlett-Packard           Presario 2100 (DM964A)   /0024                     , BIOS KAM1.44 06/23/200392
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0x2bef0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-DEFFF uncachable
[    0.000000]   DF000-DFFFF write-protect
[    0.000000]   E0000-E3FFF write-back
[    0.000000]   E4000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FE0000000 write-back
[    0.000000]   1 base 020000000 mask FF8000000 write-back
[    0.000000]   2 base 028000000 mask FFC000000 write-back
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] initial memory mapped : 0 - 01800000
[    0.000000] Base memory trampoline at [c009c000] 9c000 size 12288
[    0.000000] init_memory_mapping: 0000000000000000-000000002bef0000
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 002bc00000 page 2M
[    0.000000]  002bc00000 - 002bef0000 page 4k
[    0.000000] kernel direct mapping tables up to 2bef0000 @ 17fa000-1800000
[    0.000000] RAMDISK: 2af99000 - 2babb000
[    0.000000] ACPI: RSDP 000f7450 00014 (v00 PTLTD )
[    0.000000] ACPI: RSDT 2bef8bf5 00030 (v01 PTLTD    RSDT   06040000  LTP 00000000)
[    0.000000] ACPI: FACP 2befee2b 00074 (v01 ATI    Raptor   06040000 ATI  000F4240)
[    0.000000] ACPI: DSDT 2bef8c25 06206 (v01    ATI U1_M1535 06040000 MSFT 0100000D)
[    0.000000] ACPI: FACS 2befffc0 00040
[    0.000000] ACPI: BOOT 2befee9f 00028 (v01 PTLTD  $SBFTBL$ 06040000  LTP 00000001)
[    0.000000] ACPI: SSDT 2befeec7 00139 (v01 PTLTD  POWERNOW 06040000  LTP 00000001)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 702MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 2bef0000
[    0.000000]   low ram: 0 - 2bef0000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x0002bef0
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0002bef0
[    0.000000] On node 0 totalpages: 179839
[    0.000000] free_area_init_node: node 0, pgdat c13c5488, node_mem_map eaa19200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1374 pages used for memmap
[    0.000000]   Normal zone: 174482 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x8008
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] APIC: disable apic facility
[    0.000000] APIC: switched to apic NOOP
[    0.000000] nr_irqs_gsi: 16
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
[    0.000000] PM: Registered nosave memory: 00000000000d0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 2c000000 (gap: 2c000000:d3fc0000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 178433
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.2.0-4-486 root=/dev/mapper/crunchbang-root ro quiet
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 696600k/719808k available (2588k kernel code, 22756k reserved, 1300k data, 452k init, 0k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfffa1000 - 0xfffff000   ( 376 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xec6f0000 - 0xff7fe000   ( 305 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xebef0000   ( 702 MB)
[    0.000000]       .init : 0xc13cd000 - 0xc143e000   ( 452 kB)
[    0.000000]       .data : 0xc12870ac - 0xc13cc0c0   (1300 kB)
[    0.000000]       .text : 0xc1000000 - 0xc12870ac   (2588 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] NR_IRQS:2304 nr_irqs:256 16
[    0.000000] CPU 0 irqstacks, hard=ea406000 soft=ea408000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1855.357 MHz processor.
[    0.008004] Calibrating delay loop (skipped), value calculated using timer frequency.. 3710.71 BogoMIPS (lpj=7421428)
[    0.008011] pid_max: default: 32768 minimum: 301
[    0.008075] Security Framework initialized
[    0.008088] AppArmor: AppArmor disabled by boot time parameter
[    0.008110] Mount-cache hash table entries: 512
[    0.008325] Initializing cgroup subsys cpuacct
[    0.008331] Initializing cgroup subsys memory
[    0.008344] Initializing cgroup subsys devices
[    0.008348] Initializing cgroup subsys freezer
[    0.008351] Initializing cgroup subsys net_cls
[    0.008355] Initializing cgroup subsys blkio
[    0.008366] Initializing cgroup subsys perf_event
[    0.008426] CPU: mobile AMD Athlon(tm) XP2500+ stepping 00
[    0.008872] ACPI: Core revision 20110623
[    0.012308] ACPI: setting ELCR to 0200 (from 0e28)
[    0.014344] Performance Events: 
[    0.014351] no APIC, boot with the "lapic" boot parameter to force-enable it.
[    0.014354] no hardware sampling interrupt available.
[    0.014359] AMD PMU driver.
[    0.014364] ... version:                0
[    0.014367] ... bit width:              48
[    0.014370] ... generic registers:      4
[    0.014372] ... value mask:             0000ffffffffffff
[    0.014375] ... max period:             00007fffffffffff
[    0.014378] ... fixed-purpose events:   0
[    0.014380] ... event mask:             000000000000000f
[    0.014773] NMI watchdog disabled (cpu0): not supported (no LAPIC?)
[    0.015033] devtmpfs: initialized
[    0.015246] PM: Registering ACPI NVS region at 2beff000 (4096 bytes)
[    0.015528] print_constraints: dummy: 
[    0.015626] NET: Registered protocol family 16
[    0.015802] EISA bus registered
[    0.015874] ACPI: bus type pci registered
[    0.016353] PCI: PCI BIOS revision 2.10 entry at 0xfd87b, last bus=2
[    0.016357] PCI: Using configuration type 1 for base access
[    0.017470] bio: create slab <bio-0> at 0
[    0.017604] ACPI: Added _OSI(Module Device)
[    0.017608] ACPI: Added _OSI(Processor Device)
[    0.017611] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.017615] ACPI: Added _OSI(Processor Aggregator Device)
[    0.018461] ACPI: EC: Look up EC in DSDT
[    0.028205] ACPI: Interpreter enabled
[    0.028222] ACPI: (supports S0 S3 S4 S5)
[    0.028252] ACPI: Using PIC for interrupt routing
[    0.036381] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
[    0.036512] ACPI: No dock devices found.
[    0.036516] HEST: Table not found.
[    0.036525] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[    0.036692] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.037010] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[    0.037016] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000c3fff] (ignored)
[    0.037020] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000c7fff] (ignored)
[    0.037024] pci_root PNP0A03:00: host bridge window [mem 0x000c8000-0x000cbfff] (ignored)
[    0.037028] pci_root PNP0A03:00: host bridge window [mem 0x000cc000-0x000cffff] (ignored)
[    0.037033] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000d7fff] (ignored)
[    0.037037] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000cefff] (ignored)
[    0.037041] pci_root PNP0A03:00: host bridge window [mem 0x2c000000-0xfff7ffff] (ignored)
[    0.037045] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7] (ignored)
[    0.037049] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff] (ignored)
[    0.037078] pci 0000:00:00.0: [1002:cab0] type 0 class 0x000600
[    0.037091] pci 0000:00:00.0: reg 10: [mem 0xd4000000-0xd7ffffff pref]
[    0.037098] pci 0000:00:00.0: reg 14: [mem 0xd0500000-0xd0500fff pref]
[    0.037104] pci 0000:00:00.0: reg 18: [io  0x8090-0x8093]
[    0.037158] pci 0000:00:01.0: [1002:700f] type 1 class 0x000604
[    0.037198] pci 0000:00:02.0: [10b9:5237] type 0 class 0x000c03
[    0.037212] pci 0000:00:02.0: reg 10: [mem 0xd0000000-0xd0000fff]
[    0.037264] pci 0000:00:02.0: PME# supported from D3cold
[    0.037288] pci 0000:00:06.0: [10b9:5451] type 0 class 0x000401
[    0.037302] pci 0000:00:06.0: reg 10: [io  0x8400-0x84ff]
[    0.037311] pci 0000:00:06.0: reg 14: [mem 0xd0001000-0xd0001fff]
[    0.037357] pci 0000:00:06.0: supports D1 D2
[    0.037360] pci 0000:00:06.0: PME# supported from D2 D3hot D3cold
[    0.037385] pci 0000:00:07.0: [10b9:1533] type 0 class 0x000601
[    0.037471] pci 0000:00:08.0: [10b9:5457] type 0 class 0x000703
[    0.037484] pci 0000:00:08.0: reg 10: [mem 0xd0002000-0xd0002fff]
[    0.037493] pci 0000:00:08.0: reg 14: [io  0x8800-0x88ff]
[    0.037537] pci 0000:00:08.0: PME# supported from D3hot D3cold
[    0.037561] pci 0000:00:0a.0: [1217:6972] type 2 class 0x000607
[    0.037576] pci 0000:00:0a.0: reg 10: [mem 0x80000000-0x80000fff]
[    0.037598] pci 0000:00:0a.0: supports D1 D2
[    0.037602] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.037629] pci 0000:00:10.0: [10b9:5229] type 0 class 0x000101
[    0.037662] pci 0000:00:10.0: reg 20: [io  0x8080-0x808f]
[    0.037707] pci 0000:00:11.0: [10b9:7101] type 0 class 0x000680
[    0.037762] pci 0000:00:11.0: quirk: [io  0x8000-0x803f] claimed by ali7101 ACPI
[    0.037767] pci 0000:00:11.0: quirk: [io  0x8040-0x805f] claimed by ali7101 SMB
[    0.037790] pci 0000:00:12.0: [100b:0020] type 0 class 0x000200
[    0.037804] pci 0000:00:12.0: reg 10: [io  0x8c00-0x8cff]
[    0.037814] pci 0000:00:12.0: reg 14: [mem 0xd0003000-0xd0003fff]
[    0.037844] pci 0000:00:12.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[    0.037865] pci 0000:00:12.0: supports D1 D2
[    0.037868] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.037919] pci 0000:01:05.0: [1002:4336] type 0 class 0x000300
[    0.037933] pci 0000:01:05.0: reg 10: [mem 0xe0000000-0xefffffff pref]
[    0.037942] pci 0000:01:05.0: reg 14: [io  0x9000-0x90ff]
[    0.037951] pci 0000:01:05.0: reg 18: [mem 0xd0100000-0xd010ffff]
[    0.037973] pci 0000:01:05.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.037999] pci 0000:01:05.0: supports D1 D2
[    0.038028] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.038035] pci 0000:00:01.0:   bridge window [io  0x9000-0x9fff]
[    0.038040] pci 0000:00:01.0:   bridge window [mem 0xd0100000-0xd01fffff]
[    0.038046] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xefffffff pref]
[    0.038053] pci 0000:00:0a.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.038087] pci_bus 0000:00: on NUMA node 0
[    0.038093] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.038175] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[    0.038240]  pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e)
[    0.040622] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 *10)
[    0.040725] ACPI: PCI Interrupt Link [LNKB] (IRQs 7 *11)
[    0.040823] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 10) *0, disabled.
[    0.040923] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 10) *0, disabled.
[    0.041022] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 10) *0, disabled.
[    0.041122] ACPI: PCI Interrupt Link [LNKF] (IRQs 7 *11)
[    0.041219] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 6 10)
[    0.041316] ACPI: PCI Interrupt Link [LNKH] (IRQs *5 7)
[    0.041413] ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 6 10) *9
[    0.041583] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
[    0.041588] vgaarb: loaded
[    0.041590] vgaarb: bridge control possible 0000:01:05.0
[    0.041689] PCI: Using ACPI for IRQ routing
[    0.041695] PCI: pci_cache_line_size set to 32 bytes
[    0.041736] reserve RAM buffer: 000000000009f800 - 000000000009ffff 
[    0.041741] reserve RAM buffer: 000000002bef0000 - 000000002bffffff 
[    0.041963] Switching to clocksource pit
[    0.042721] pnp: PnP ACPI init
[    0.042759] ACPI: bus type pnp registered
[    0.043039] pnp 00:00: [bus 00-ff]
[    0.043049] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.043054] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[    0.043058] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[    0.043062] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[    0.043066] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[    0.043070] pnp 00:00: [mem 0x000d0000-0x000d7fff window]
[    0.043074] pnp 00:00: [mem 0x000a0000-0x000cefff window]
[    0.043078] pnp 00:00: [mem 0x2c000000-0xfff7ffff window]
[    0.043083] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.043086] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.043090] pnp 00:00: [io  0x0d00-0xffff window]
[    0.043209] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.043440] pnp 00:01: [io  0x0000-0x000f]
[    0.043444] pnp 00:01: [io  0x0081-0x008f]
[    0.043448] pnp 00:01: [io  0x00c0-0x00df]
[    0.043453] pnp 00:01: [dma 4]
[    0.043504] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.043526] pnp 00:02: [io  0x0070-0x0073]
[    0.043534] pnp 00:02: [irq 8]
[    0.043581] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.043598] pnp 00:03: [io  0x00f0-0x00fe]
[    0.043602] pnp 00:03: [irq 13]
[    0.043649] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.043665] pnp 00:04: [io  0x0061]
[    0.043715] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.043732] pnp 00:05: [io  0x0060]
[    0.043736] pnp 00:05: [io  0x0064]
[    0.043740] pnp 00:05: [irq 1]
[    0.043787] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.043804] pnp 00:06: [irq 12]
[    0.043856] pnp 00:06: Plug and Play ACPI device, IDs SYN0105 SYN0100 SYN0002 PNP0f13 (active)
[    0.043880] pnp 00:07: [io  0x0080]
[    0.043884] pnp 00:07: [io  0x00b0-0x00b3]
[    0.043887] pnp 00:07: [io  0x0092]
[    0.043891] pnp 00:07: [io  0x040b]
[    0.043894] pnp 00:07: [io  0x0480-0x048f]
[    0.043898] pnp 00:07: [io  0x04d0-0x04d1]
[    0.043901] pnp 00:07: [io  0x04d6]
[    0.043905] pnp 00:07: [io  0x8000-0x807f]
[    0.043908] pnp 00:07: [io  0xff00-0xff01]
[    0.043912] pnp 00:07: [io  0x8004-0x8005]
[    0.043915] pnp 00:07: [io  0xfe00-0xfefe]
[    0.043919] pnp 00:07: [mem 0xe0500000-0xe0500fff]
[    0.043923] pnp 00:07: [mem 0xd0500000-0xd0500fff]
[    0.043940] pnp 00:07: disabling [mem 0xe0500000-0xe0500fff] because it overlaps 0000:00:01.0 BAR 15 [mem 0xe0000000-0xefffffff pref]
[    0.043969] pnp 00:07: disabling [io  0x8004-0x8005] because it overlaps 0000:00:11.0 BAR 13 [io  0x8000-0x803f]
[    0.043981] pnp 00:07: disabling [mem 0xe0500000-0xe0500fff disabled] because it overlaps 0000:01:05.0 BAR 0 [mem 0xe0000000-0xefffffff pref]
[    0.044044] system 00:07: [io  0x040b] has been reserved
[    0.044049] system 00:07: [io  0x0480-0x048f] has been reserved
[    0.044054] system 00:07: [io  0x04d0-0x04d1] has been reserved
[    0.044058] system 00:07: [io  0x04d6] has been reserved
[    0.044062] system 00:07: [io  0x8000-0x807f] could not be reserved
[    0.044066] system 00:07: [io  0xff00-0xff01] has been reserved
[    0.044071] system 00:07: [io  0xfe00-0xfefe] has been reserved
[    0.044077] system 00:07: [mem 0xd0500000-0xd0500fff] has been reserved
[    0.044083] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.044637] pnp 00:08: [io  0x0378-0x037f]
[    0.044641] pnp 00:08: [io  0x0778-0x077f]
[    0.044645] pnp 00:08: [irq 7]
[    0.044648] pnp 00:08: [dma 0]
[    0.045028] pnp 00:08: Plug and Play ACPI device, IDs PNP0401 (active)
[    0.045281] pnp 00:09: [io  0x03f8-0x03ff]
[    0.045286] pnp 00:09: [irq 4]
[    0.045378] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.045518] pnp: PnP ACPI: found 10 devices
[    0.045521] ACPI: ACPI bus type pnp unregistered
[    0.045528] PnPBIOS: Disabled by ACPI PNP
[    0.083475] Switching to clocksource acpi_pm
[    0.083500] PCI: max bus depth: 1 pci_try_num: 2
[    0.083530] pci 0000:00:12.0: BAR 6: assigned [mem 0x2c000000-0x2c00ffff pref]
[    0.083538] pci 0000:00:0a.0: BAR 16: assigned [mem 0x30000000-0x33ffffff]
[    0.083544] pci 0000:00:0a.0: BAR 15: assigned [mem 0x34000000-0x37ffffff pref]
[    0.083550] pci 0000:00:0a.0: BAR 14: assigned [io  0x1000-0x10ff]
[    0.083556] pci 0000:00:0a.0: BAR 13: assigned [io  0x1400-0x14ff]
[    0.083562] pci 0000:01:05.0: BAR 6: assigned [mem 0xd0120000-0xd013ffff pref]
[    0.083567] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.083572] pci 0000:00:01.0:   bridge window [io  0x9000-0x9fff]
[    0.083578] pci 0000:00:01.0:   bridge window [mem 0xd0100000-0xd01fffff]
[    0.083584] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xefffffff pref]
[    0.083591] pci 0000:00:0a.0: CardBus bridge to [bus 02-05]
[    0.083595] pci 0000:00:0a.0:   bridge window [io  0x1400-0x14ff]
[    0.083600] pci 0000:00:0a.0:   bridge window [io  0x1000-0x10ff]
[    0.083605] pci 0000:00:0a.0:   bridge window [mem 0x34000000-0x37ffffff pref]
[    0.083611] pci 0000:00:0a.0:   bridge window [mem 0x30000000-0x33ffffff]
[    0.083790] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
[    0.083796] PCI: setting IRQ 11 as level-triggered
[    0.083805] pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
[    0.083809] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[    0.083813] pci_bus 0000:01: resource 0 [io  0x9000-0x9fff]
[    0.083817] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd01fffff]
[    0.083821] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff pref]
[    0.083825] pci_bus 0000:02: resource 0 [io  0x1400-0x14ff]
[    0.083828] pci_bus 0000:02: resource 1 [io  0x1000-0x10ff]
[    0.083832] pci_bus 0000:02: resource 2 [mem 0x34000000-0x37ffffff pref]
[    0.083836] pci_bus 0000:02: resource 3 [mem 0x30000000-0x33ffffff]
[    0.083934] NET: Registered protocol family 2
[    0.084050] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.084751] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.088230] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[    0.088988] TCP: Hash tables configured (established 131072 bind 65536)
[    0.088992] TCP reno registered
[    0.088998] UDP hash table entries: 512 (order: 1, 8192 bytes)
[    0.089028] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
[    0.089241] NET: Registered protocol family 1
[    0.089266] pci 0000:00:00.0: ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb
[    0.089560] ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 10
[    0.089566] PCI: setting IRQ 10 as level-triggered
[    0.360076] pci 0000:00:07.0: Activating ISA DMA hang workarounds
[    0.360108] pci 0000:01:05.0: Boot video device
[    0.360113] PCI: CLS 64 bytes, default 32
[    0.360238] Unpacking initramfs...
[    0.811797] Freeing initrd memory: 11400k freed
[    0.839369] Simple Boot Flag at 0x36 set to 0x1
[    0.840759] audit: initializing netlink socket (disabled)
[    0.840788] type=2000 audit(1364546272.839:1): initialized
[    0.857995] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.858155] VFS: Disk quotas dquot_6.5.2
[    0.858187] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.858290] msgmni has been set to 1382
[    0.858562] alg: No test for stdrng (krng)
[    0.858600] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.858607] io scheduler noop registered
[    0.858609] io scheduler deadline registered
[    0.858620] io scheduler cfq registered (default)
[    0.858812] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.858855] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.858859] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.859331] ERST: Table is not found!
[    0.859334] GHES: HEST is not enabled!
[    0.859354] isapnp: Scanning for PnP cards...
[    1.126404] isapnp: No Plug & Play device found
[    1.126517] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.147055] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.168020] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.168392] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 3
[    1.168398] PCI: setting IRQ 3 as level-triggered
[    1.168576] Linux agpgart interface v0.103
[    1.168614] agpgart-ati 0000:00:00.0: Ati IGP320/M chipset
[    1.169057] reserve_ram_pages_type failed 0x28725000-0x28726000, track 0x10, req 0x10
[    1.169528] reserve_ram_pages_type failed 0x28726000-0x28727000, track 0x10, req 0x10
[    1.169999] reserve_ram_pages_type failed 0x28727000-0x28728000, track 0x10, req 0x10
[    1.170469] reserve_ram_pages_type failed 0x28728000-0x28729000, track 0x10, req 0x10
[    1.170939] reserve_ram_pages_type failed 0x28729000-0x2872a000, track 0x10, req 0x10
[    1.171417] reserve_ram_pages_type failed 0x28730000-0x28731000, track 0x10, req 0x10
[    1.171888] reserve_ram_pages_type failed 0x28731000-0x28732000, track 0x10, req 0x10
[    1.172435] reserve_ram_pages_type failed 0x28732000-0x28733000, track 0x10, req 0x10
[    1.172905] reserve_ram_pages_type failed 0x28733000-0x28734000, track 0x10, req 0x10
[    1.173376] reserve_ram_pages_type failed 0x28734000-0x28735000, track 0x10, req 0x10
[    1.173846] reserve_ram_pages_type failed 0x28735000-0x28736000, track 0x10, req 0x10
[    1.174317] reserve_ram_pages_type failed 0x28736000-0x28737000, track 0x10, req 0x10
[    1.174787] reserve_ram_pages_type failed 0x28737000-0x28738000, track 0x10, req 0x10
[    1.175258] reserve_ram_pages_type failed 0x28738000-0x28739000, track 0x10, req 0x10
[    1.175728] reserve_ram_pages_type failed 0x28739000-0x2873a000, track 0x10, req 0x10
[    1.176276] reserve_ram_pages_type failed 0x2873a000-0x2873b000, track 0x10, req 0x10
[    1.176746] reserve_ram_pages_type failed 0x2873b000-0x2873c000, track 0x10, req 0x10
[    1.177990] agpgart-ati 0000:00:00.0: AGP aperture is 64M @ 0xd4000000
[    1.178370] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[    1.180574] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.180591] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.180817] mousedev: PS/2 mouse device common for all mice
[    1.181088] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    1.181119] rtc0: alarms up to one month, y3k, 242 bytes nvram
[    1.181202] EISA: Probing bus 0 at eisa.0
[    1.181217] Cannot allocate resource for EISA slot 1
[    1.181250] Cannot allocate resource for EISA slot 8
[    1.181253] EISA: Detected 0 cards.
[    1.181258] cpuidle: using governor ladder
[    1.181261] cpuidle: using governor menu
[    1.181592] TCP cubic registered
[    1.181624] NET: Registered protocol family 10
[    1.182300] Mobile IPv6
[    1.182305] NET: Registered protocol family 17
[    1.182312] Registering the dns_resolver key type
[    1.182338] Using IPI Shortcut mode
[    1.182503] PM: Hibernation image not present or could not be loaded.
[    1.182536] registered taskstats version 1
[    1.182869] rtc_cmos 00:02: setting system clock to 2013-03-29 08:37:55 UTC (1364546275)
[    1.182932] Initializing network drop monitor service
[    1.183157] Freeing unused kernel memory: 452k freed
[    1.184192] Write protecting the kernel text: 2592k
[    1.184226] Write protecting the kernel read-only data: 1036k
[    1.213905] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.264377] udevd[45]: starting version 175
[    1.365353] natsemi dp8381x driver, version 2.1, Sept 11, 2006
[    1.365357]   originally by Donald Becker <becker@scyld.com>
[    1.365359]   2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
[    1.365694] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[    1.396983] natsemi eth0: NatSemi DP8381[56] at 0xd0003000 (0000:00:12.0), 00:0b:cd:e9:cc:cf, IRQ 11, port TP.
[    1.424232] thermal LNXTHERM:00: registered as thermal_zone0
[    1.424239] ACPI: Thermal Zone [THRM] (47 C)
[    1.438078] usbcore: registered new interface driver usbfs
[    1.438133] usbcore: registered new interface driver hub
[    1.444950] usbcore: registered new device driver usb
[    1.446000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.446493] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.446580] ohci_hcd 0000:00:02.0: OHCI Host Controller
[    1.446637] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[    1.446678] ohci_hcd 0000:00:02.0: irq 10, io mem 0xd0000000
[    1.452498] SCSI subsystem initialized
[    1.502136] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    1.502143] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.502147] usb usb1: Product: OHCI Host Controller
[    1.502151] usb usb1: Manufacturer: Linux 3.2.0-4-486 ohci_hcd
[    1.502154] usb usb1: SerialNumber: 0000:00:02.0
[    1.502439] hub 1-0:1.0: USB hub found
[    1.502451] hub 1-0:1.0: 4 ports detected
[    1.523075] libata version 3.00 loaded.
[    1.523676] pata_ali 0000:00:10.0: can't derive routing for PCI INT A
[    1.527261] scsi0 : pata_ali
[    1.531271] scsi1 : pata_ali
[    1.531604] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8080 irq 14
[    1.531609] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8088 irq 15
[    1.696490] ata1.00: ATA-6: IC25N030ATMR04-0, MOAOAD0A, max UDMA/100
[    1.696498] ata1.00: 58605120 sectors, multi 16: LBA48 
[    1.712359] ata1.00: configured for UDMA/100
[    1.712656] scsi 0:0:0:0: Direct-Access     ATA      IC25N030ATMR04-0 MOAO PQ: 0 ANSI: 5
[    1.856129] Refined TSC clocksource calibration: 1855.187 MHz.
[    1.856141] Switching to clocksource tsc
[    1.876339] ata2.00: ATAPI: TOSHIBA DVD-ROM SD-R2312, 1905, max MWDMA2
[    1.876346] ata2.00: WARNING: ATAPI DMA disabled for reliability issues.  It can be enabled
[    1.876350] ata2.00: WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.
[    1.892249] ata2.00: configured for MWDMA2
[    1.898206] scsi 1:0:0:0: CD-ROM            TOSHIBA  DVD-ROM SD-R2312 1905 PQ: 0 ANSI: 5
[    1.914364] sd 0:0:0:0: [sda] 58605120 512-byte logical blocks: (30.0 GB/27.9 GiB)
[    1.914453] sd 0:0:0:0: [sda] Write Protect is off
[    1.914458] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.914495] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.917699] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    1.917707] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.918311] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.272977]  sda: sda1 sda2 < sda5 >
[    2.273595] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.284755] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.284873] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    2.653477] microcode: CPU0: family 6 not supported
[    2.654098] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    2.670351] device-mapper: uevent: version 1.0.3
[    2.670946] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    2.935491] ACPI: EC: GPE storm detected, transactions will use polling mode
[   20.032239] PM: Starting manual resume from disk
[   20.032250] PM: Hibernation image partition 254:2 present
[   20.032253] PM: Looking for hibernation image.
[   20.032773] PM: Image not found (code -22)
[   20.032777] PM: Hibernation image not present or could not be loaded.
[   20.107128] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[   22.898295] udevd[347]: starting version 175
[   23.422390] Marking TSC unstable due to TSC halts in idle
[   23.422410] ACPI: acpi_idle registered with cpuidle
[   23.424621] Switching to clocksource acpi_pm
[   23.432525] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[   23.432542] ACPI: Power Button [PWRB]
[   23.432660] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[   23.442537] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:01/LNXVIDEO:00/input/input3
[   23.442555] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   23.468372] ACPI: Lid Switch [LID]
[   23.468586] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[   23.468600] ACPI: Power Button [PWRF]
[   23.468904] ACPI: AC Adapter [ACAD] (on-line)
[   23.469004] ACPI: Battery Slot [BAT1] (battery absent)
[   23.523461] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   23.651749] parport_pc 00:08: reported by Plug and Play ACPI
[   23.651825] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[   23.654739] yenta_cardbus 0000:00:0a.0: CardBus bridge found [103c:0024]
[   23.654765] yenta_cardbus 0000:00:0a.0: O2: enabling read prefetch/write burst. If you experience problems or performance issues, use the yenta_socket parameter 'o2_speedup=off'
[   23.780617] yenta_cardbus 0000:00:0a.0: ISA IRQ mask 0x0038, PCI irq 11
[   23.780624] yenta_cardbus 0000:00:0a.0: Socket status: 30000828
[   23.922371] input: PC Speaker as /devices/platform/pcspkr/input/input5
[   23.933283] pci 0000:00:11.0: enabling device (0000 -> 0001)
[   23.933547] ALi_M1535: initialized. timeout=60 sec (nowayout=0)
[   23.935286] alim7101_wdt: Steve Hill <steve@navaho.co.uk>.
[   23.935307] alim7101_wdt: Detected old alim7101 revision 'a1d'.  If this is a cobalt board, set the 'use_gpio' module parameter.
[   24.133406] powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
[   24.136351] Fast TSC calibration using PIT
[   24.143477] powernow: No PST tables match this cpuid (0x7a0)
[   24.143481] powernow: This is indicative of a broken BIOS.
[   24.143483] powernow: Trying ACPI perflib
[   24.144321] powernow: Minimum speed 530 MHz. Maximum speed 1855 MHz.
[   24.237432] alim7101_wdt: Steve Hill <steve@navaho.co.uk>.
[   24.237451] alim7101_wdt: Detected old alim7101 revision 'a1d'.  If this is a cobalt board, set the 'use_gpio' module parameter.
[   24.498844] [drm] Initialized drm 1.1.0 20060810
[   24.673339] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[   24.673410] pci 0000:02:00.0: [1814:0401] type 0 class 0x000280
[   24.673458] pci 0000:02:00.0: reg 10: [mem 0xffff8000-0xffffffff]
[   24.673616] pci 0000:02:00.0: BAR 0: assigned [mem 0x30000000-0x30007fff]
[   24.769309] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
[   24.769327] PCI: setting IRQ 5 as level-triggered
[   24.912864] psmouse serio1: synaptics: Touchpad model: 1, fw: 5.8, id: 0x2348b3, caps: 0x904713/0x10008/0x0
[   24.951047] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[   25.121159] [drm] radeon kernel modesetting enabled.
[   25.121481] radeon 0000:01:05.0: power state changed by ACPI to D0
[   25.121503] radeon 0000:01:05.0: power state changed by ACPI to D0
[   25.122116] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[   25.124209] [drm] initializing kernel modesetting (RS100 0x1002:0x4336 0x103C:0x0024).
[   25.124304] [drm] register mmio base: 0xD0100000
[   25.124315] [drm] register mmio size: 65536
[   25.125104] agpgart-ati 0000:00:00.0: AGP 2.0 bridge
[   25.125148] agpgart-ati 0000:00:00.0: putting AGP V2 device into 4x mode
[   25.125224] radeon 0000:01:05.0: putting AGP V2 device into 4x mode
[   25.125252] radeon 0000:01:05.0: GTT: 64M 0xD4000000 - 0xD7FFFFFF
[   25.125275] radeon 0000:01:05.0: VRAM: 64M 0x000000002C000000 - 0x000000002FFFFFFF (64M used)
[   25.125311] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   25.125322] [drm] Driver supports precise vblank timestamp query.
[   25.125360] [drm] radeon: irq initialized.
[   25.125934] [drm] Detected VRAM RAM=64M, BAR=256M
[   25.125951] [drm] RAM width 64bits DDR
[   25.126245] [TTM] Zone  kernel: Available graphics memory: 354226 kiB.
[   25.126258] [TTM] Initializing pool allocator.
[   25.126387] [drm] radeon: 64M of VRAM memory ready
[   25.126399] [drm] radeon: 64M of GTT memory ready.
[   25.151784] radeon 0000:01:05.0: WB disabled
[   25.154239] [drm] Loading R100 Microcode
[   25.410893] platform radeon_cp.0: firmware: agent loaded radeon/R100_cp.bin into memory
[   25.413853] [drm] radeon: ring at 0x00000000D4001000
[   25.413888] [drm] ring test succeeded in 0 usecs
[   25.414757] [drm] radeon: ib pool ready.
[   25.414982] [drm] ib test succeeded in 0 usecs
[   25.419950] [drm] Panel ID String: LGP                     
[   25.419965] [drm] Panel Size 1024x768
[   25.432629] [drm] radeon legacy LVDS backlight initialized
[   25.434395] [drm] Radeon Display Connectors
[   25.434406] [drm] Connector 0:
[   25.434414] [drm]   VGA
[   25.434427] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[   25.434436] [drm]   Encoders:
[   25.434445] [drm]     CRT1: INTERNAL_DAC1
[   25.434454] [drm] Connector 1:
[   25.434461] [drm]   LVDS
[   25.434473] [drm]   DDC: 0x198 0x198 0x19c 0x19c 0x1a0 0x1a0 0x1a4 0x1a4
[   25.434482] [drm]   Encoders:
[   25.434489] [drm]     LCD1: INTERNAL_LVDS
[   25.434497] [drm] Connector 2:
[   25.434504] [drm]   S-video
[   25.434510] [drm]   Encoders:
[   25.434518] [drm]     TV1: INTERNAL_DAC2
[   25.565109] cfg80211: Calling CRDA to update world regulatory domain
[   25.589074] [drm] fb mappable at 0xE0040000
[   25.589080] [drm] vram apper at 0xE0000000
[   25.589082] [drm] size 3145728
[   25.589085] [drm] fb depth is 24
[   25.589087] [drm]    pitch is 4096
[   25.589453] fbcon: radeondrmfb (fb0) is primary device
[   25.667560] Console: switching to colour frame buffer device 128x48
[   25.682455] fb0: radeondrmfb frame buffer device
[   25.682459] drm: registered panic notifier
[   25.682479] [drm] Initialized radeon 2.12.0 20080528 for 0000:01:05.0 on minor 0
[   26.117115] rt61pci 0000:02:00.0: enabling device (0000 -> 0002)
[   26.117174] rt61pci 0000:02:00.0: setting latency timer to 64
[   26.193507] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   26.196828] Registered led device: rt61pci-phy0::radio
[   26.197073] Registered led device: rt61pci-phy0::assoc
[   27.150989] cfg80211: World regulatory domain updated:
[   27.151009] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   27.151026] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   27.151042] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   27.151057] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   27.151071] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   27.151086] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   27.844065] AC'97 1 does not respond - RESET
[   27.860059] AC'97 1 access is not valid [0xffffffff], removing mixer.
[   27.860317] ali mixer 1 creating error.
[   28.381164] EXT4-fs (dm-1): re-mounted. Opts: (null)
[   28.836841] EXT4-fs (dm-1): re-mounted. Opts: errors=remount-ro
[   29.322138] loop: module loaded
[   31.478061] Adding 1228796k swap on /dev/mapper/crunchbang-swap_1.  Priority:-1 extents:1 across:1228796k 
[   42.325000] rt61pci 0000:02:00.0: firmware: agent loaded rt2661.bin into memory
[   42.365039] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   42.403626] eth0: DSPCFG accepted after 0 usec.
[   42.420683] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   56.930669] fuse init (API version 7.17)
[  185.444148] wlan0: authenticate with 90:01:3b:81:e8:50 (try 1)
[  185.455331] wlan0: authenticated
[  185.484154] wlan0: associate with 90:01:3b:81:e8:50 (try 1)
[  185.539858] wlan0: RX AssocResp from 90:01:3b:81:e8:50 (capab=0x411 status=0 aid=2)
[  185.539879] wlan0: associated
[  185.542550] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

Offline

#6 2013-03-29 09:36:27

xaos52
The Good Doctor
From: Planet of the @s
Registered: 2011-06-24
Posts: 4,602

Re: Strange wifi behavior

Could not see anything wrong in the info you posted.

1/ Check output of

sudo iwconfig

for power management on your wifi interface.

2/ Post output of

sudo iw wlan0 station dump

3/ Post output of

sudo grep -Ei 'wpa|net' /var/log/syslog | tail -n 400

after provoking the incident and then rebooting  (so that syslog buffers get flushed)
Better post that to a paste board and publish a link to it.

Cheers,
xaos

Last edited by xaos52 (2013-03-29 09:38:08)

Offline

#7 2013-03-29 12:02:29

cyrixblack
Member
Registered: 2013-03-13
Posts: 21

Re: Strange wifi behavior

wlan0     IEEE 802.11bg  ESSID:"SKY1E84F"  
          Mode:Managed  Frequency:2.462 GHz  Access Point: 90:01:3B:81:E8:50   
          Bit Rate=36 Mb/s   Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=68/70  Signal level=-42 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:36  Invalid misc:188   Missed beacon:0

eth0      no wireless extensions.
Station 90:01:3b:81:e8:50 (on wlan0)
	inactive time:	1784 ms
	rx bytes:	10599474
	rx packets:	33838
	tx bytes:	1290828
	tx packets:	8534
	tx retries:	3621
	tx failed:	36
	signal:  	-46 dBm
	signal avg:	-42 dBm
	tx bitrate:	36.0 MBit/s
	authorized:	yes
	authenticated:	yes
	preamble:	long
	WMM/WME:	yes
	MFP:		no

Offline

#8 2013-03-29 12:03:58

cyrixblack
Member
Registered: 2013-03-13
Posts: 21

Re: Strange wifi behavior

Mar 28 22:19:24 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:19:24 crunchbang NetworkManager[1874]: <info> Config: set interface ap_scan to 1
Mar 28 22:19:24 crunchbang NetworkManager[1874]: <info> (wlan0): supplicant interface state: inactive -> scanning
Mar 28 22:19:25 crunchbang wpa_supplicant[1957]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:19:25 crunchbang NetworkManager[1874]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:19:25 crunchbang wpa_supplicant[1957]: wlan0: Trying to associate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:19:25 crunchbang NetworkManager[1874]: <info> (wlan0): supplicant interface state: authenticating -> associating
Mar 28 22:19:25 crunchbang wpa_supplicant[1957]: wlan0: Associated with 90:01:3b:81:e8:50
Mar 28 22:19:25 crunchbang kernel: [  128.314365] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Mar 28 22:19:25 crunchbang NetworkManager[1874]: <info> (wlan0): supplicant interface state: associating -> associated
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> (wlan0): supplicant interface state: associated -> 4-way handshake
Mar 28 22:19:26 crunchbang wpa_supplicant[1957]: wlan0: WPA: Key negotiation completed with 90:01:3b:81:e8:50 [PTK=CCMP GTK=TKIP]
Mar 28 22:19:26 crunchbang wpa_supplicant[1957]: wlan0: CTRL-EVENT-CONNECTED - Connection to 90:01:3b:81:e8:50 completed (auth) [id=0 id_str=]
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> (wlan0): supplicant interface state: 4-way handshake -> completed
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> Activation (wlan0/wireless) Stage 2 of 5 (Device Configure) successful.  Connected to wireless network 'SKY1E84F'.
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) scheduled.
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) started...
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> (wlan0): device state change: config -> ip-config (reason 'none') [50 70 0]
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Beginning DHCPv4 transaction (timeout in 45 seconds)
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> dhclient started with pid 2315
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Beginning IP6 addrconf.
Mar 28 22:19:26 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) complete.
Mar 28 22:19:27 crunchbang dhclient: Internet Systems Consortium DHCP Client 4.2.2
Mar 28 22:19:27 crunchbang dhclient: Copyright 2004-2011 Internet Systems Consortium.
Mar 28 22:19:27 crunchbang NetworkManager[1874]: <info> (wlan0): DHCPv4 state changed nbi -> preinit
Mar 28 22:19:34 crunchbang NetworkManager[1874]: <info> (wlan0): DHCPv4 state changed preinit -> bound
Mar 28 22:19:34 crunchbang NetworkManager[1874]: <info>   address 192.168.0.10
Mar 28 22:19:34 crunchbang NetworkManager[1874]: <info>   prefix 24 (255.255.255.0)
Mar 28 22:19:34 crunchbang NetworkManager[1874]: <info>   gateway 192.168.0.1
Mar 28 22:19:34 crunchbang NetworkManager[1874]: <info>   nameserver '192.168.0.1'
Mar 28 22:19:34 crunchbang NetworkManager[1874]: <info>   domain name 'Home'
Mar 28 22:19:34 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 5 of 5 (IPv4 Configure Commit) scheduled...
Mar 28 22:19:34 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 5 of 5 (IPv4 Commit) started...
Mar 28 22:19:35 crunchbang NetworkManager[1874]: <info> (wlan0): device state change: ip-config -> activated (reason 'none') [70 100 0]
Mar 28 22:19:35 crunchbang NetworkManager[1874]: <info> Policy set 'SKY1E84F' (wlan0) as default for IPv4 routing and DNS.
Mar 28 22:19:35 crunchbang NetworkManager[1874]: <info> Activation (wlan0) successful, device activated.
Mar 28 22:19:35 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 5 of 5 (IPv4 Commit) complete.
Mar 28 22:19:45 crunchbang NetworkManager[1874]: <info> (wlan0): IP6 addrconf timed out or failed.
Mar 28 22:19:45 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled...
Mar 28 22:19:45 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 4 of 5 (IPv6 Configure Timeout) started...
Mar 28 22:19:45 crunchbang NetworkManager[1874]: <info> Activation (wlan0) Stage 4 of 5 (IPv6 Configure Timeout) complete.
Mar 28 22:37:34 crunchbang NetworkManager[1874]: <info> caught signal 15, shutting down normally.
Mar 28 22:37:34 crunchbang NetworkManager[1874]: <warn> quit request received, terminating...
Mar 28 22:37:34 crunchbang NetworkManager[1874]: <info> (wlan0): now unmanaged
Mar 28 22:37:34 crunchbang NetworkManager[1874]: <info> (wlan0): device state change: activated -> unmanaged (reason 'removed') [100 10 36]
Mar 28 22:37:34 crunchbang NetworkManager[1874]: <info> (wlan0): deactivating device (reason 'removed') [36]
Mar 28 22:37:35 crunchbang NetworkManager[1874]: <info> (wlan0): canceled DHCP transaction, DHCP client pid 2315
Mar 28 22:37:35 crunchbang wpa_supplicant[1957]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=3
Mar 28 22:37:35 crunchbang NetworkManager[1874]: <info> (wlan0): cleaning up...
Mar 28 22:37:35 crunchbang NetworkManager[1874]: <info> (wlan0): taking down device.
Mar 28 22:37:35 crunchbang NetworkManager[1874]: <info> (eth0): now unmanaged
Mar 28 22:37:35 crunchbang NetworkManager[1874]: <info> (eth0): device state change: unavailable -> unmanaged (reason 'removed') [20 10 36]
Mar 28 22:37:35 crunchbang NetworkManager[1874]: <info> (eth0): cleaning up...
Mar 28 22:37:35 crunchbang NetworkManager[1874]: <info> (eth0): taking down device.
Mar 28 22:37:35 crunchbang NetworkManager[1874]: <info> exiting (success)
Mar 28 22:42:09 crunchbang kernel: [    0.008351] Initializing cgroup subsys net_cls
Mar 28 22:42:09 crunchbang kernel: [    0.015598] NET: Registered protocol family 16
Mar 28 22:42:09 crunchbang kernel: [    0.115887] NET: Registered protocol family 2
Mar 28 22:42:09 crunchbang kernel: [    0.121304] NET: Registered protocol family 1
Mar 28 22:42:09 crunchbang kernel: [    0.872796] audit: initializing netlink socket (disabled)
Mar 28 22:42:09 crunchbang kernel: [    1.213681] NET: Registered protocol family 10
Mar 28 22:42:09 crunchbang kernel: [    1.214362] NET: Registered protocol family 17
Mar 28 22:42:09 crunchbang kernel: [    1.214989] Initializing network drop monitor service
Mar 28 22:42:09 crunchbang kernel: [    2.369564] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
Mar 28 22:42:12 crunchbang avahi-daemon[1769]: Network interface enumeration completed.
Mar 28 22:42:13 crunchbang kernel: [   40.865887] NET: Registered protocol family 31
Mar 28 22:42:13 crunchbang kernel: [   41.087711] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Mar 28 22:42:15 crunchbang NetworkManager[1871]: <info> NetworkManager (version 0.9.4.0) is starting...
Mar 28 22:42:15 crunchbang NetworkManager[1871]: <info> Read config file /etc/NetworkManager/NetworkManager.conf
Mar 28 22:42:17 crunchbang NetworkManager[1871]: <info> VPN: loaded org.freedesktop.NetworkManager.pptp
Mar 28 22:42:17 crunchbang NetworkManager[1871]: <info> VPN: loaded org.freedesktop.NetworkManager.vpnc
Mar 28 22:42:17 crunchbang NetworkManager[1871]: <info> VPN: loaded org.freedesktop.NetworkManager.openvpn
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: init!
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: update_system_hostname
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPluginIfupdown: management mode: unmanaged
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:0a.0/0000:02:00.0/net/wlan0, iface: wlan0)
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:0a.0/0000:02:00.0/net/wlan0, iface: wlan0): no ifupdown configuration found.
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:12.0/net/eth0, iface: eth0)
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:12.0/net/eth0, iface: eth0): no ifupdown configuration found.
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/lo, iface: lo)
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/lo, iface: lo): no ifupdown configuration found.
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: end _init.
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> Loaded plugin ifupdown: (C) 2008 Canonical Ltd.  To report bugs please use the NetworkManager mailing list.
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> Loaded plugin keyfile: (c) 2007 - 2010 Red Hat, Inc.  To report bugs please use the NetworkManager mailing list.
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    Ifupdown: get unmanaged devices count: 0
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: (168394496) ... get_connections.
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    SCPlugin-Ifupdown: (168394496) ... get_connections (managed=false): return empty list.
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    keyfile: parsing SKY1E84F ... 
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    keyfile:     read connection 'SKY1E84F'
Mar 28 22:42:18 crunchbang NetworkManager[1871]:    Ifupdown: get unmanaged devices count: 0
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> trying to start the modem manager...
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> monitoring kernel firmware directory '/lib/firmware'.
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> found WiFi radio killswitch rfkill0 (at /sys/devices/pci0000:00/0000:00:0a.0/0000:02:00.0/ieee80211/phy0/rfkill0) (driver (unknown))
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> WiFi enabled by radio killswitch; enabled by state file
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> WWAN enabled by radio killswitch; enabled by state file
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> WiMAX enabled by radio killswitch; enabled by state file
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> Networking is enabled by state file
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (wlan0): using nl80211 for WiFi device control
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <warn> (wlan0): driver supports Access Point (AP) mode
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt61pci' ifindex: 3)
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/0
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (wlan0): now managed
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (wlan0): bringing up device.
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (wlan0): preparing device.
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (wlan0): deactivating device (reason 'managed') [2]
Mar 28 22:42:18 crunchbang kernel: [   46.600887] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Mar 28 22:42:18 crunchbang dbus[1756]: [system] Activating service name='fi.w1.wpa_supplicant1' (using servicehelper)
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <warn> failed to allocate link cache: (-10) Operation not supported
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (eth0): carrier is OFF
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (eth0): new Ethernet device (driver: 'natsemi' ifindex: 2)
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (eth0): exported as /org/freedesktop/NetworkManager/Devices/1
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (eth0): now managed
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (eth0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (eth0): bringing up device.
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (eth0): preparing device.
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> (eth0): deactivating device (reason 'managed') [2]
Mar 28 22:42:18 crunchbang kernel: [   46.632134] ADDRCONF(NETDEV_UP): eth0: link is not ready
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> Added default wired connection 'Wired connection 1' for /sys/devices/pci0000:00/0000:00:12.0/net/eth0
Mar 28 22:42:18 crunchbang NetworkManager[1871]: <info> modem-manager is now available
Mar 28 22:42:19 crunchbang dbus[1756]: [system] Successfully activated service 'fi.w1.wpa_supplicant1'
Mar 28 22:42:19 crunchbang NetworkManager[1871]: <info> wpa_supplicant started
Mar 28 22:42:19 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: starting -> ready
Mar 28 22:42:19 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42]
Mar 28 22:42:19 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: ready -> inactive
Mar 28 22:42:19 crunchbang NetworkManager[1871]: <warn> Trying to remove a non-existant call id.
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Auto-activating connection 'SKY1E84F'.
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Activation (wlan0) starting connection 'SKY1E84F'
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): connection 'SKY1E84F' has security, and secrets exist.  No new secrets needed.
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Config: added 'ssid' value 'SKY1E84F'
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Config: added 'scan_ssid' value '1'
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Config: added 'auth_alg' value 'OPEN'
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Config: added 'psk' value '<omitted>'
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> Config: set interface ap_scan to 1
Mar 28 22:46:40 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: inactive -> scanning
Mar 28 22:46:41 crunchbang wpa_supplicant[1953]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:46:41 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:46:42 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: authenticating -> disconnected
Mar 28 22:46:42 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:47:05 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): association took too long.
Mar 28 22:47:05 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Mar 28 22:47:05 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): asking for new secrets
Mar 28 22:47:05 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> disconnected
Mar 28 22:47:05 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:47:15 crunchbang NetworkManager[1871]: get_secret_flags: assertion `is_secret_prop (setting, secret_name, error)' failed
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): connection 'SKY1E84F' has security, and secrets exist.  No new secrets needed.
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Config: added 'ssid' value 'SKY1E84F'
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Config: added 'scan_ssid' value '1'
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Config: added 'auth_alg' value 'OPEN'
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Config: added 'psk' value '<omitted>'
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> Config: set interface ap_scan to 1
Mar 28 22:47:15 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:47:23 crunchbang wpa_supplicant[1953]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:47:23 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:47:23 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: authenticating -> disconnected
Mar 28 22:47:23 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> (wlan0): disconnecting for new activation request.
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> disconnected (reason 'none') [50 30 0]
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> (wlan0): deactivating device (reason 'none') [0]
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Activation (wlan0) starting connection 'SKY1E84F'
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> disconnected
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): connection 'SKY1E84F' has security, and secrets exist.  No new secrets needed.
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Config: added 'ssid' value 'SKY1E84F'
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Config: added 'scan_ssid' value '1'
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Config: added 'auth_alg' value 'OPEN'
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Config: added 'psk' value '<omitted>'
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:47:35 crunchbang NetworkManager[1871]: <info> Config: set interface ap_scan to 1
Mar 28 22:47:36 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:47:55 crunchbang wpa_supplicant[1953]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:47:55 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:47:55 crunchbang wpa_supplicant[1953]: wlan0: Trying to associate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:47:55 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: authenticating -> associating
Mar 28 22:47:56 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: associating -> disconnected
Mar 28 22:47:56 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:48:01 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): association took too long.
Mar 28 22:48:01 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Mar 28 22:48:01 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): asking for new secrets
Mar 28 22:48:01 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> disconnected
Mar 28 22:48:01 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:48:16 crunchbang NetworkManager[1871]: get_secret_flags: assertion `is_secret_prop (setting, secret_name, error)' failed
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): connection 'SKY1E84F' has security, and secrets exist.  No new secrets needed.
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Config: added 'ssid' value 'SKY1E84F'
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Config: added 'scan_ssid' value '1'
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Config: added 'auth_alg' value 'OPEN'
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Config: added 'psk' value '<omitted>'
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> Config: set interface ap_scan to 1
Mar 28 22:48:16 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:48:42 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): association took too long.
Mar 28 22:48:42 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Mar 28 22:48:42 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): asking for new secrets
Mar 28 22:48:42 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:48:42 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:48:42 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> inactive
Mar 28 22:48:47 crunchbang NetworkManager[1871]: <warn> No agents were available for this request.
Mar 28 22:48:47 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: need-auth -> failed (reason 'no-secrets') [60 120 7]
Mar 28 22:48:47 crunchbang NetworkManager[1871]: <warn> Activation (wlan0) failed for access point (SKY1E84F)
Mar 28 22:48:47 crunchbang NetworkManager[1871]: <info> Marking connection 'SKY1E84F' invalid.
Mar 28 22:48:47 crunchbang NetworkManager[1871]: <warn> Activation (wlan0) failed.
Mar 28 22:48:47 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0]
Mar 28 22:48:47 crunchbang NetworkManager[1871]: <info> (wlan0): deactivating device (reason 'none') [0]
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) starting connection 'SKY1E84F'
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): access point 'SKY1E84F' has security, but secrets are required.
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): connection 'SKY1E84F' has security, and secrets exist.  No new secrets needed.
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Config: added 'ssid' value 'SKY1E84F'
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Config: added 'scan_ssid' value '1'
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Config: added 'psk' value '<omitted>'
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> Config: set interface ap_scan to 1
Mar 28 22:48:52 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: inactive -> scanning
Mar 28 22:49:05 crunchbang wpa_supplicant[1953]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:49:05 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:49:06 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: authenticating -> disconnected
Mar 28 22:49:06 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:49:07 crunchbang wpa_supplicant[1953]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:49:07 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:49:08 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: authenticating -> disconnected
Mar 28 22:49:08 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:49:09 crunchbang wpa_supplicant[1953]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:49:09 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:49:09 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: authenticating -> disconnected
Mar 28 22:49:10 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:49:17 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): association took too long.
Mar 28 22:49:17 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Mar 28 22:49:17 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): asking for new secrets
Mar 28 22:49:17 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> disconnected
Mar 28 22:49:17 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:50:17 crunchbang NetworkManager[1871]: get_secret_flags: assertion `is_secret_prop (setting, secret_name, error)' failed
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): connection 'SKY1E84F' has security, and secrets exist.  No new secrets needed.
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Config: added 'ssid' value 'SKY1E84F'
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Config: added 'scan_ssid' value '1'
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Config: added 'psk' value '<omitted>'
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> Config: set interface ap_scan to 1
Mar 28 22:50:17 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:50:36 crunchbang wpa_supplicant[1953]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:50:36 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:50:37 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: authenticating -> disconnected
Mar 28 22:50:37 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:50:38 crunchbang wpa_supplicant[1953]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:50:38 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:50:39 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: authenticating -> disconnected
Mar 28 22:50:39 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:50:42 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): association took too long.
Mar 28 22:50:42 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Mar 28 22:50:42 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): asking for new secrets
Mar 28 22:50:42 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> disconnected
Mar 28 22:50:42 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:50:46 crunchbang NetworkManager[1871]: get_secret_flags: assertion `is_secret_prop (setting, secret_name, error)' failed
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): connection 'SKY1E84F' has security, and secrets exist.  No new secrets needed.
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Config: added 'ssid' value 'SKY1E84F'
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Config: added 'scan_ssid' value '1'
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Config: added 'psk' value '<omitted>'
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> Config: set interface ap_scan to 1
Mar 28 22:50:46 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:51:11 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): association took too long.
Mar 28 22:51:11 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Mar 28 22:51:11 crunchbang NetworkManager[1871]: <warn> Activation (wlan0/wireless): asking for new secrets
Mar 28 22:51:11 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:51:11 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:51:12 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> inactive
Mar 28 22:52:14 crunchbang NetworkManager[1871]: <warn> No agents were available for this request.
Mar 28 22:52:14 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: need-auth -> failed (reason 'no-secrets') [60 120 7]
Mar 28 22:52:14 crunchbang NetworkManager[1871]: <warn> Activation (wlan0) failed for access point (SKY1E84F)
Mar 28 22:52:14 crunchbang NetworkManager[1871]: <info> Marking connection 'SKY1E84F' invalid.
Mar 28 22:52:14 crunchbang NetworkManager[1871]: <warn> Activation (wlan0) failed.
Mar 28 22:52:14 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0]
Mar 28 22:52:14 crunchbang NetworkManager[1871]: <info> (wlan0): deactivating device (reason 'none') [0]
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Auto-activating connection 'SKY1E84F'.
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) starting connection 'SKY1E84F'
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): access point 'SKY1E84F' has security, but secrets are required.
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): connection 'SKY1E84F' has security, and secrets exist.  No new secrets needed.
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Config: added 'ssid' value 'SKY1E84F'
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Config: added 'scan_ssid' value '1'
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Config: added 'psk' value '<omitted>'
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> Config: set interface ap_scan to 1
Mar 28 22:57:14 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: inactive -> scanning
Mar 28 22:57:17 crunchbang NetworkManager[1871]: <info> (wlan0): disconnecting for new activation request.
Mar 28 22:57:17 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> disconnected (reason 'none') [50 30 0]
Mar 28 22:57:17 crunchbang NetworkManager[1871]: <info> (wlan0): deactivating device (reason 'none') [0]
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Activation (wlan0) starting connection 'SKY1E84F'
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Activation (wlan0/wireless): connection 'SKY1E84F' has security, and secrets exist.  No new secrets needed.
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Config: added 'ssid' value 'SKY1E84F'
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Config: added 'scan_ssid' value '1'
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Config: added 'psk' value '<omitted>'
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <warn> Couldn't disconnect supplicant interface: This interface is not connected.
Mar 28 22:57:18 crunchbang NetworkManager[1871]: <info> Config: set interface ap_scan to 1
Mar 28 22:57:27 crunchbang wpa_supplicant[1953]: wlan0: SME: Trying to authenticate with 90:01:3b:81:e8:50 (SSID='SKY1E84F' freq=2462 MHz)
Mar 28 22:57:27 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: scanning -> authenticating
Mar 28 22:57:28 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: authenticating -> disconnected
Mar 28 22:57:28 crunchbang NetworkManager[1871]: <info> (wlan0): supplicant interface state: disconnected -> scanning
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> caught signal 15, shutting down normally.
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <warn> quit request received, terminating...
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> (wlan0): now unmanaged
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> (wlan0): device state change: config -> unmanaged (reason 'removed') [50 10 36]
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> (wlan0): deactivating device (reason 'removed') [36]
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> (wlan0): cleaning up...
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> (wlan0): taking down device.
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> (eth0): now unmanaged
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> (eth0): device state change: unavailable -> unmanaged (reason 'removed') [20 10 36]
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> (eth0): cleaning up...
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> (eth0): taking down device.
Mar 28 22:57:37 crunchbang NetworkManager[1871]: <info> exiting (success)

I tried wicd but that just didnt work at all so I reverted back to nm-applet.

Offline

#9 2013-03-29 15:00:42

xaos52
The Good Doctor
From: Planet of the @s
Registered: 2011-06-24
Posts: 4,602

Re: Strange wifi behavior

No power managemeny for the wifi device. We can exclude that.

I can see attempts to connect that fail.
Try eliminating network-manager, using this thread.
Let us know if that helps.

Cheers,
xaos

Last edited by xaos52 (2013-03-29 15:01:38)

Offline

#10 2013-03-29 15:15:42

dura
Bloated Gimp
From: interzone
Registered: 2012-09-15
Posts: 2,106

Re: Strange wifi behavior

Some wifi in kernels up until 3.8. Disconnect issues affecting lots of wifi mentioned in the Arch forums. Since kernel 3.8 I'm getting more stable and faster wifi than Apple devices, etc. maybe unrelated info.

Last edited by dura (2013-03-29 15:16:28)

Offline

Board footer

Powered by FluxBB

Copyright © 2012 CrunchBang Linux.
Proudly powered by Debian. Hosted by Linode.
Debian is a registered trademark of Software in the Public Interest, Inc.

Debian Logo