You are not logged in.
- Topics: Active | Unanswered
#1 2012-05-15 17:33:53
My wireless disconnects constantly
Hi. I'm using crunchbang since a few months ago. I love the usability and minimalism of it. The only problem I have is with the wireless card.
lspci -nn | grep Network
01:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01)The wireless works, but suddenly is disconnected :S with no possibility to connect again. I've tried to down the interface (wlan0) and up it again, restart network-manager, deactivating and activating the wireless and nothing. The only solutions that seems to work is restarting the system (wich is not always possible).
The firmware I'm using is the "firmware-brcm80211" and the kernel driver is brcmsmac
Offline
Help fund CrunchBang, donate to the project!
#2 2012-05-15 18:12:35
- pvsage
- Internal Affairs
- From: North Carolina
- Registered: 2009-10-18
- Posts: 9,012
Re: My wireless disconnects constantly
Maybe a pio/qos problem? Try this:
http://crunchbanglinux.org/forums/post/140261/#p140261
Seems to only be an issue with certain routers...
while ( ! ( succeed = try() ) );
We've earned a reputation as a nice, friendly community; please help us keep it that way.
Online
#4 2012-05-15 21:41:53
Re: My wireless disconnects constantly
I did what it says on the post and reboot. Now I don't have wireless. I've got this messages from dmesg
dmesg | grep brcmsmac
[ 9.612528] brcmsmac: Unknown parameter `pio'Last edited by nuxero (2012-05-15 21:42:11)
Offline
#5 2012-05-16 00:34:05
- pvsage
- Internal Affairs
- From: North Carolina
- Registered: 2009-10-18
- Posts: 9,012
Re: My wireless disconnects constantly
Sorry about that - apparently that hack just works with the lp-phy chips like the 4312. For now, if
cat /etc/modprobe.d/b43.confreturns just the one line, then just
sudo rm /etc/modprobe.d/b43.confand you should at least have your intermittent wifi back.
The Dr. should be back in tomorrow to help with the differential diagnosis.
while ( ! ( succeed = try() ) );
We've earned a reputation as a nice, friendly community; please help us keep it that way.
Online
#7 2012-05-16 06:55:38
- xaos52
- The Good Doctor
- From: Planet of the @s
- Registered: 2011-06-24
- Posts: 4,290
Re: My wireless disconnects constantly
Hi nuxero,
Post output of
uname -r
dmesg
lsmodThere are several possibilties to get your card working, but you should not combine them or they step on each others foot.
bootinfoscript - emacs primer - I ♥ #!
Offline
#8 2012-05-17 02:33:36
Re: My wireless disconnects constantly
Sure 
here it is
uname -r
3.2.0-0.bpo.2-686-paedmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-0.bpo.2-686-pae (Debian 3.2.15-1~bpo60+1) (debian-kernel@lists.debian.org) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Mon Apr 23 09:33:57 UTC 2012
[ 0.000000] Disabled fast string operations
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f43f000 (usable)
[ 0.000000] BIOS-e820: 000000003f43f000 - 000000003f4bf000 (reserved)
[ 0.000000] BIOS-e820: 000000003f4bf000 - 000000003f5bf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f5bf000 - 000000003f5ff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003f5ff000 - 000000003f600000 (usable)
[ 0.000000] BIOS-e820: 000000003f600000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: Hewlett-Packard HP Mini 110-3500 /1584, BIOS F.14 11/30/2010
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x3f600 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFE00000 mask 0FFE00000 write-protect
[ 0.000000] 1 base 000000000 mask 0E0000000 write-back
[ 0.000000] 2 base 020000000 mask 0E0000000 write-back
[ 0.000000] 3 base 03F800000 mask 0FF800000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01a00000
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037800000 page 2M
[ 0.000000] 0037800000 - 00379fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 379fe000 @ 19fa000-1a00000
[ 0.000000] RAMDISK: 2ea07000 - 2f770000
[ 0.000000] ACPI: RSDP 000fe020 00024 (v02 HPQOEM)
[ 0.000000] ACPI: XSDT 3f5fe120 00074 (v01 HPQOEM SLIC-MPC 00000001 01000013)
[ 0.000000] ACPI: FACP 3f5fd000 000F4 (v04 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: DSDT 3f5f2000 07DD6 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: FACS 3f583000 00040
[ 0.000000] ACPI: HPET 3f5fc000 00038 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: APIC 3f5fb000 00078 (v02 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: MCFG 3f5fa000 0003C (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: SLIC 3f5f1000 00176 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: BOOT 3f5f0000 00028 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: SSDT 3f5ef000 00628 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 3f5ee000 00259 (v01 PmRef Cpu0Tst 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 3f5ed000 0020F (v01 PmRef ApTst 00003000 INTL 20051117)
[ 0.000000] ACPI: WDAT 3f5ec000 00194 (v01 INSYDE INSYDE 00000001 MSFT 01000013)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 124MB HIGHMEM available.
[ 0.000000] 889MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 379fe000
[ 0.000000] low ram: 0 - 379fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000379fe
[ 0.000000] HighMem 0x000379fe -> 0x0003f600
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003f43f
[ 0.000000] 0: 0x0003f5ff -> 0x0003f600
[ 0.000000] On node 0 totalpages: 259023
[ 0.000000] free_area_init_node: node 0, pgdat c1424000, node_mem_map f720d200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1748 pages used for memmap
[ 0.000000] Normal zone: 221994 pages, LIFO batch:31
[ 0.000000] HighMem zone: 249 pages used for memmap
[ 0.000000] HighMem zone: 31049 pages, LIFO batch:7
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:a0000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @f7000000 s33088 r0 d24256 u524288
[ 0.000000] pcpu-alloc: s33088 r0 d24256 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256994
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-0.bpo.2-686-pae root=UUID=bcfe8b15-4150-4943-ac46-c61d0809638a ro quiet splash splash
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000379fe:0003f600)
[ 0.000000] Memory: 1007852k/1038336k available (2925k kernel code, 28240k reserved, 1344k data, 436k init, 125192k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
[ 0.000000] .init : 0xc142c000 - 0xc1499000 ( 436 kB)
[ 0.000000] .data : 0xc12db62d - 0xc142b8c0 (1344 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12db62d (2925 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:712 16
[ 0.000000] CPU 0 irqstacks, hard=f6806000 soft=f6808000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1662.279 MHz processor.
[ 0.004004] Calibrating delay loop (skipped), value calculated using timer frequency.. 3324.55 BogoMIPS (lpj=6649116)
[ 0.004015] pid_max: default: 32768 minimum: 301
[ 0.004101] Security Framework initialized
[ 0.004109] AppArmor: AppArmor disabled by boot time parameter
[ 0.004144] Mount-cache hash table entries: 512
[ 0.008097] Initializing cgroup subsys cpuacct
[ 0.008110] Initializing cgroup subsys memory
[ 0.008125] Initializing cgroup subsys devices
[ 0.008130] Initializing cgroup subsys freezer
[ 0.008136] Initializing cgroup subsys net_cls
[ 0.008141] Initializing cgroup subsys blkio
[ 0.008153] Initializing cgroup subsys perf_event
[ 0.008200] Disabled fast string operations
[ 0.008208] CPU: Physical Processor ID: 0
[ 0.008212] CPU: Processor Core ID: 0
[ 0.008217] mce: CPU supports 5 MCE banks
[ 0.008230] CPU0: Thermal monitoring enabled (TM2)
[ 0.008236] using mwait in idle threads.
[ 0.009503] ACPI: Core revision 20110623
[ 0.020102] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.020610] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.061501] CPU0: Intel(R) Atom(TM) CPU N455 @ 1.66GHz stepping 0a
[ 0.064003] Performance Events: PEBS fmt0+, Atom events, Intel PMU driver.
[ 0.064003] ... version: 3
[ 0.064003] ... bit width: 40
[ 0.064003] ... generic registers: 2
[ 0.064003] ... value mask: 000000ffffffffff
[ 0.064003] ... max period: 000000007fffffff
[ 0.064003] ... fixed-purpose events: 3
[ 0.064003] ... event mask: 0000000700000003
[ 0.064003] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.064003] CPU 1 irqstacks, hard=f68f2000 soft=f68f4000
[ 0.064003] Booting Node 0, Processors #1
[ 0.064003] smpboot cpu 1: start_ip = 9b000
[ 0.008000] Initializing CPU#1
[ 0.008000] Disabled fast string operations
[ 0.152068] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.152140] Brought up 2 CPUs
[ 0.152148] Total of 2 processors activated (6649.47 BogoMIPS).
[ 0.152712] devtmpfs: initialized
[ 0.152712] PM: Registering ACPI NVS region at 3f4bf000 (1048576 bytes)
[ 0.152712] print_constraints: dummy:
[ 0.152712] NET: Registered protocol family 16
[ 0.152825] ACPI: bus type pci registered
[ 0.152994] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.153003] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.153008] PCI: Using MMCONFIG for extended config space
[ 0.153013] PCI: Using configuration type 1 for base access
[ 0.156140] bio: create slab <bio-0> at 0
[ 0.156226] ACPI: Added _OSI(Module Device)
[ 0.156226] ACPI: Added _OSI(Processor Device)
[ 0.156226] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.156226] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.158868] ACPI: EC: Look up EC in DSDT
[ 0.164468] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.165569] ACPI: SSDT 3f497790 00731 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.166666] ACPI: Dynamic OEM Table Load:
[ 0.166673] ACPI: SSDT (null) 00731 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.167007] ACPI: SSDT 3f495690 00646 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.167667] ACPI: Dynamic OEM Table Load:
[ 0.167674] ACPI: SSDT (null) 00646 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.188676] ACPI: SSDT 3f496d90 0015F (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.189425] ACPI: Dynamic OEM Table Load:
[ 0.189432] ACPI: SSDT (null) 0015F (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.200260] ACPI: SSDT 3f496f10 0008D (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.200950] ACPI: Dynamic OEM Table Load:
[ 0.200957] ACPI: SSDT (null) 0008D (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.816171] ACPI: Interpreter enabled
[ 0.816187] ACPI: (supports S0 S3 S4 S5)
[ 0.816248] ACPI: Using IOAPIC for interrupt routing
[ 0.841831] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[ 0.842122] ACPI: No dock devices found.
[ 0.842128] HEST: Table not found.
[ 0.842138] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.843043] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20110623/nspredef-359)
[ 0.843061] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.843066] _OSC request data:1 8 1f
[ 0.843077] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.844641] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.844649] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.844656] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.844665] pci_root PNP0A08:00: host bridge window [mem 0x40000000-0xfebfffff]
[ 0.844692] pci 0000:00:00.0: [8086:a010] type 0 class 0x000600
[ 0.844758] pci 0000:00:02.0: [8086:a011] type 0 class 0x000300
[ 0.844775] pci 0000:00:02.0: reg 10: [mem 0x56180000-0x561fffff]
[ 0.844786] pci 0000:00:02.0: reg 14: [io 0x40c0-0x40c7]
[ 0.844796] pci 0000:00:02.0: reg 18: [mem 0x40000000-0x4fffffff pref]
[ 0.844807] pci 0000:00:02.0: reg 1c: [mem 0x56000000-0x560fffff]
[ 0.844858] pci 0000:00:02.1: [8086:a012] type 0 class 0x000380
[ 0.844872] pci 0000:00:02.1: reg 10: [mem 0x56100000-0x5617ffff]
[ 0.844987] pci 0000:00:1b.0: [8086:27d8] type 0 class 0x000403
[ 0.845015] pci 0000:00:1b.0: reg 10: [mem 0x56200000-0x56203fff 64bit]
[ 0.845123] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.845132] pci 0000:00:1b.0: PME# disabled
[ 0.845170] pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
[ 0.845275] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.845284] pci 0000:00:1c.0: PME# disabled
[ 0.845330] pci 0000:00:1c.2: [8086:27d4] type 1 class 0x000604
[ 0.845442] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.845450] pci 0000:00:1c.2: PME# disabled
[ 0.845491] pci 0000:00:1c.3: [8086:27d6] type 1 class 0x000604
[ 0.845596] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.845605] pci 0000:00:1c.3: PME# disabled
[ 0.845648] pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
[ 0.845709] pci 0000:00:1d.0: reg 20: [io 0x4080-0x409f]
[ 0.845762] pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
[ 0.845823] pci 0000:00:1d.1: reg 20: [io 0x4060-0x407f]
[ 0.845877] pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
[ 0.845936] pci 0000:00:1d.2: reg 20: [io 0x4040-0x405f]
[ 0.845989] pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
[ 0.846049] pci 0000:00:1d.3: reg 20: [io 0x4020-0x403f]
[ 0.846116] pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
[ 0.846146] pci 0000:00:1d.7: reg 10: [mem 0x56204400-0x562047ff]
[ 0.846261] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.846270] pci 0000:00:1d.7: PME# disabled
[ 0.846301] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.846403] pci 0000:00:1f.0: [8086:27bc] type 0 class 0x000601
[ 0.846580] pci 0000:00:1f.2: [8086:27c1] type 0 class 0x000106
[ 0.846607] pci 0000:00:1f.2: reg 10: [io 0x40b8-0x40bf]
[ 0.846623] pci 0000:00:1f.2: reg 14: [io 0x40cc-0x40cf]
[ 0.846638] pci 0000:00:1f.2: reg 18: [io 0x40b0-0x40b7]
[ 0.846653] pci 0000:00:1f.2: reg 1c: [io 0x40c8-0x40cb]
[ 0.846669] pci 0000:00:1f.2: reg 20: [io 0x40a0-0x40af]
[ 0.846684] pci 0000:00:1f.2: reg 24: [mem 0x56204000-0x562043ff]
[ 0.846742] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.846750] pci 0000:00:1f.2: PME# disabled
[ 0.846778] pci 0000:00:1f.3: [8086:27da] type 0 class 0x000c05
[ 0.846854] pci 0000:00:1f.3: reg 20: [io 0x4000-0x401f]
[ 0.847018] pci 0000:01:00.0: [14e4:4727] type 0 class 0x000280
[ 0.847066] pci 0000:01:00.0: reg 10: [mem 0x55000000-0x55003fff 64bit]
[ 0.847302] pci 0000:01:00.0: supports D1 D2
[ 0.847396] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.847405] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.847413] pci 0000:00:1c.0: bridge window [mem 0x55000000-0x55ffffff]
[ 0.847426] pci 0000:00:1c.0: bridge window [mem 0x50000000-0x50ffffff 64bit pref]
[ 0.847494] pci 0000:00:1c.2: PCI bridge to [bus 02-02]
[ 0.847503] pci 0000:00:1c.2: bridge window [io 0x2000-0x2fff]
[ 0.847512] pci 0000:00:1c.2: bridge window [mem 0x54000000-0x54ffffff]
[ 0.847525] pci 0000:00:1c.2: bridge window [mem 0x51000000-0x51ffffff 64bit pref]
[ 0.847661] pci 0000:03:00.0: [10ec:8136] type 0 class 0x000200
[ 0.847731] pci 0000:03:00.0: reg 10: [io 0x1000-0x10ff]
[ 0.847848] pci 0000:03:00.0: reg 18: [mem 0x52004000-0x52004fff 64bit pref]
[ 0.847925] pci 0000:03:00.0: reg 20: [mem 0x52000000-0x52003fff 64bit pref]
[ 0.848237] pci 0000:03:00.0: supports D1 D2
[ 0.848243] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.848260] pci 0000:03:00.0: PME# disabled
[ 0.848438] pci 0000:00:1c.3: PCI bridge to [bus 03-03]
[ 0.848447] pci 0000:00:1c.3: bridge window [io 0x1000-0x1fff]
[ 0.848455] pci 0000:00:1c.3: bridge window [mem 0x53000000-0x53ffffff]
[ 0.848468] pci 0000:00:1c.3: bridge window [mem 0x52000000-0x52ffffff 64bit pref]
[ 0.848564] pci 0000:00:1e.0: PCI bridge to [bus 04-04] (subtractive decode)
[ 0.848581] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.848588] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.848596] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.848603] pci 0000:00:1e.0: bridge window [mem 0x40000000-0xfebfffff] (subtractive decode)
[ 0.848636] pci_bus 0000:00: on NUMA node 0
[ 0.848644] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.848939] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.849124] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 0.849248] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
[ 0.849365] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
[ 0.849629] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20110623/nspredef-359)
[ 0.849647] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.849651] _OSC request data:1 1f 1f
[ 0.849662] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.849795] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20110623/nspredef-359)
[ 0.849812] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.849816] _OSC request data:1 0 1d
[ 0.849826] pci0000:00: ACPI _OSC request failed (AE_TYPE), returned control mask: 0x1d
[ 0.849831] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.855694] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.855840] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.855992] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.856145] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.856289] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.856434] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.856579] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.856723] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.857069] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.857069] vgaarb: loaded
[ 0.857069] vgaarb: bridge control possible 0000:00:02.0
[ 0.857069] PCI: Using ACPI for IRQ routing
[ 0.866040] PCI: pci_cache_line_size set to 64 bytes
[ 0.866158] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.866165] reserve RAM buffer: 000000003f43f000 - 000000003fffffff
[ 0.866173] reserve RAM buffer: 000000003f600000 - 000000003fffffff
[ 0.866428] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.866440] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.866451] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.872216] Switching to clocksource hpet
[ 0.875495] pnp: PnP ACPI init
[ 0.875534] ACPI: bus type pnp registered
[ 0.881618] pnp 00:00: [bus 00-ff]
[ 0.881625] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.881632] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.881638] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.881644] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.881650] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.881656] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.881663] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.881669] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.881675] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.881681] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.881687] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.881693] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.881700] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.881706] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.881712] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.881722] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.881728] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.881734] pnp 00:00: [mem 0x40000000-0xfebfffff window]
[ 0.881852] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.882145] pnp 00:01: [io 0x164e-0x164f]
[ 0.882152] pnp 00:01: [io 0x0061]
[ 0.882157] pnp 00:01: [io 0x0070]
[ 0.882162] pnp 00:01: [io 0x0080]
[ 0.882167] pnp 00:01: [io 0x0092]
[ 0.882173] pnp 00:01: [io 0x00b2-0x00b3]
[ 0.882178] pnp 00:01: [io 0x0063]
[ 0.882183] pnp 00:01: [io 0x0065]
[ 0.882188] pnp 00:01: [io 0x0067]
[ 0.882194] pnp 00:01: [io 0x0600-0x060f]
[ 0.882199] pnp 00:01: [io 0x0610]
[ 0.882204] pnp 00:01: [io 0x0800-0x080f]
[ 0.882210] pnp 00:01: [io 0x0810-0x0817]
[ 0.882215] pnp 00:01: [io 0x0400-0x047f]
[ 0.882221] pnp 00:01: [io 0x0500-0x053f]
[ 0.882227] pnp 00:01: [mem 0xe0000000-0xefffffff]
[ 0.882233] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[ 0.882239] pnp 00:01: [mem 0xfed14000-0xfed17fff]
[ 0.882244] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[ 0.882250] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[ 0.882256] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[ 0.882262] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[ 0.882299] pnp 00:01: disabling [io 0x164e-0x164f] because it overlaps 0000:00:1c.3 BAR 13 [io 0x1000-0x1fff]
[ 0.882423] system 00:01: [io 0x0600-0x060f] has been reserved
[ 0.882431] system 00:01: [io 0x0610] has been reserved
[ 0.882438] system 00:01: [io 0x0800-0x080f] has been reserved
[ 0.882446] system 00:01: [io 0x0810-0x0817] has been reserved
[ 0.882453] system 00:01: [io 0x0400-0x047f] has been reserved
[ 0.882460] system 00:01: [io 0x0500-0x053f] has been reserved
[ 0.882469] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.882476] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.882484] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[ 0.882492] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.882499] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.882508] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.882515] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.882524] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.882551] pnp 00:02: [io 0x0000-0x001f]
[ 0.882557] pnp 00:02: [io 0x0081-0x0091]
[ 0.882562] pnp 00:02: [io 0x0093-0x009f]
[ 0.882567] pnp 00:02: [io 0x00c0-0x00df]
[ 0.882573] pnp 00:02: [dma 4]
[ 0.882644] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.882704] pnp 00:03: [io 0x0070-0x0077]
[ 0.882777] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.882804] pnp 00:04: [irq 0 disabled]
[ 0.882822] pnp 00:04: [irq 8]
[ 0.882828] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 0.882906] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.882935] pnp 00:05: [io 0x00f0]
[ 0.882947] pnp 00:05: [irq 13]
[ 0.883020] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.883049] pnp 00:06: [mem 0xff800000-0xffffffff]
[ 0.883125] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.883179] pnp 00:07: [io 0x0060]
[ 0.883185] pnp 00:07: [io 0x0064]
[ 0.883196] pnp 00:07: [irq 1]
[ 0.883272] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.883319] pnp 00:08: [irq 12]
[ 0.883397] pnp 00:08: Plug and Play ACPI device, IDs SYN1e3c PNP0f13 (active)
[ 0.883513] pnp: PnP ACPI: found 9 devices
[ 0.883517] ACPI: ACPI bus type pnp unregistered
[ 0.883524] PnPBIOS: Disabled by ACPI PNP
[ 0.924837] PCI: max bus depth: 1 pci_try_num: 2
[ 0.924895] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.924904] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.924915] pci 0000:00:1c.0: bridge window [mem 0x55000000-0x55ffffff]
[ 0.924925] pci 0000:00:1c.0: bridge window [mem 0x50000000-0x50ffffff 64bit pref]
[ 0.924937] pci 0000:00:1c.2: PCI bridge to [bus 02-02]
[ 0.924945] pci 0000:00:1c.2: bridge window [io 0x2000-0x2fff]
[ 0.924955] pci 0000:00:1c.2: bridge window [mem 0x54000000-0x54ffffff]
[ 0.924965] pci 0000:00:1c.2: bridge window [mem 0x51000000-0x51ffffff 64bit pref]
[ 0.924977] pci 0000:00:1c.3: PCI bridge to [bus 03-03]
[ 0.924984] pci 0000:00:1c.3: bridge window [io 0x1000-0x1fff]
[ 0.924994] pci 0000:00:1c.3: bridge window [mem 0x53000000-0x53ffffff]
[ 0.925003] pci 0000:00:1c.3: bridge window [mem 0x52000000-0x52ffffff 64bit pref]
[ 0.925015] pci 0000:00:1e.0: PCI bridge to [bus 04-04]
[ 0.925064] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.925076] pci 0000:00:1c.0: setting latency timer to 64
[ 0.925098] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.925107] pci 0000:00:1c.2: setting latency timer to 64
[ 0.925128] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.925137] pci 0000:00:1c.3: setting latency timer to 64
[ 0.925150] pci 0000:00:1e.0: setting latency timer to 64
[ 0.925159] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.925166] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.925172] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.925179] pci_bus 0000:00: resource 7 [mem 0x40000000-0xfebfffff]
[ 0.925185] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
[ 0.925192] pci_bus 0000:01: resource 1 [mem 0x55000000-0x55ffffff]
[ 0.925199] pci_bus 0000:01: resource 2 [mem 0x50000000-0x50ffffff 64bit pref]
[ 0.925205] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 0.925212] pci_bus 0000:02: resource 1 [mem 0x54000000-0x54ffffff]
[ 0.925218] pci_bus 0000:02: resource 2 [mem 0x51000000-0x51ffffff 64bit pref]
[ 0.925225] pci_bus 0000:03: resource 0 [io 0x1000-0x1fff]
[ 0.925232] pci_bus 0000:03: resource 1 [mem 0x53000000-0x53ffffff]
[ 0.925238] pci_bus 0000:03: resource 2 [mem 0x52000000-0x52ffffff 64bit pref]
[ 0.925245] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
[ 0.925251] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
[ 0.925258] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.925264] pci_bus 0000:04: resource 7 [mem 0x40000000-0xfebfffff]
[ 0.925405] NET: Registered protocol family 2
[ 0.925559] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.926182] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.927113] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.927545] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.927551] TCP reno registered
[ 0.927561] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.927580] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.927840] NET: Registered protocol family 1
[ 0.927878] pci 0000:00:02.0: Boot video device
[ 0.927921] pci 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.927947] pci 0000:00:1d.0: PCI INT A disabled
[ 0.927979] pci 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.928038] pci 0000:00:1d.1: PCI INT B disabled
[ 0.928057] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.928082] pci 0000:00:1d.2: PCI INT C disabled
[ 0.928096] pci 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.928120] pci 0000:00:1d.3: PCI INT D disabled
[ 0.928138] pci 0000:00:1d.7: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.528031] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 2.528155] pci 0000:00:1d.7: PCI INT A disabled
[ 2.528192] PCI: CLS 64 bytes, default 64
[ 2.528319] Unpacking initramfs...
[ 3.243075] Freeing initrd memory: 13732k freed
[ 3.253929] Simple Boot Flag at 0x44 set to 0x1
[ 3.254866] audit: initializing netlink socket (disabled)
[ 3.254889] type=2000 audit(1337221498.248:1): initialized
[ 3.283635] highmem bounce pool size: 64 pages
[ 3.283647] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 3.288591] VFS: Disk quotas dquot_6.5.2
[ 3.288666] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.288805] msgmni has been set to 1750
[ 3.289214] alg: No test for stdrng (krng)
[ 3.289294] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.289301] io scheduler noop registered
[ 3.289305] io scheduler deadline registered
[ 3.289340] io scheduler cfq registered (default)
[ 3.289514] pcieport 0000:00:1c.0: setting latency timer to 64
[ 3.289596] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 3.289732] pcieport 0000:00:1c.2: setting latency timer to 64
[ 3.289804] pcieport 0000:00:1c.2: irq 41 for MSI/MSI-X
[ 3.289928] pcieport 0000:00:1c.3: setting latency timer to 64
[ 3.289998] pcieport 0000:00:1c.3: irq 42 for MSI/MSI-X
[ 3.290193] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 3.290260] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 3.290266] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 3.290808] intel_idle: MWAIT substates: 0x20220
[ 3.290825] intel_idle: v0.4 model 0x1C
[ 3.290830] intel_idle: lapic_timer_reliable_states 0x2
[ 3.290836] Marking TSC unstable due to TSC halts in idle states deeper than C2
[ 3.290922] ERST: Table is not found!
[ 3.290926] GHES: HEST is not enabled!
[ 3.290957] isapnp: Scanning for PnP cards...
[ 3.644849] isapnp: No Plug & Play device found
[ 3.645011] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 3.648777] Linux agpgart interface v0.103
[ 3.649009] agpgart-intel 0000:00:00.0: Intel GMA3150 Chipset
[ 3.649215] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
[ 3.649472] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[ 3.649722] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x40000000
[ 3.650069] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 3.665569] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.665585] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.665928] mousedev: PS/2 mouse device common for all mice
[ 3.666295] rtc_cmos 00:03: RTC can wake from S4
[ 3.666492] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 3.666535] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 3.666759] cpuidle: using governor ladder
[ 3.667057] cpuidle: using governor menu
[ 3.667635] TCP cubic registered
[ 3.667749] NET: Registered protocol family 10
[ 3.669053] Mobile IPv6
[ 3.669060] NET: Registered protocol family 17
[ 3.669069] Registering the dns_resolver key type
[ 3.669117] Using IPI No-Shortcut mode
[ 3.669447] PM: Hibernation image not present or could not be loaded.
[ 3.669473] registered taskstats version 1
[ 3.672401] rtc_cmos 00:03: setting system clock to 2012-05-17 02:24:59 UTC (1337221499)
[ 3.672559] Initializing network drop monitor service
[ 3.672791] Freeing unused kernel memory: 436k freed
[ 3.673171] Write protecting the kernel text: 2928k
[ 3.673234] Write protecting the kernel read-only data: 1088k
[ 3.673240] NX-protecting the kernel data: 3216k
[ 3.675194] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 3.705291] udev[49]: starting version 164
[ 3.775272] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 3.775291] ACPI: Power Button [PWRB]
[ 3.775527] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 3.844670] ACPI: Lid Switch [LID]
[ 3.844929] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 3.844944] ACPI: Power Button [PWRF]
[ 3.861279] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 3.861335] r8169 0000:03:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.861395] r8169 0000:03:00.0: setting latency timer to 64
[ 3.861497] r8169 0000:03:00.0: irq 43 for MSI/MSI-X
[ 3.899042] r8169 0000:03:00.0: eth0: RTL8105e at 0xf8226000, 98:4b:e1:f0:b6:45, XID 00a00000 IRQ 43
[ 3.917969] usbcore: registered new interface driver usbfs
[ 3.918044] usbcore: registered new interface driver hub
[ 3.920465] [drm] Initialized drm 1.1.0 20060810
[ 3.928286] usbcore: registered new device driver usb
[ 3.930040] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.930107] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.930157] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.930167] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.930232] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 3.930286] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 3.930309] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.934208] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 3.935047] SCSI subsystem initialized
[ 3.957838] ehci_hcd 0000:00:1d.7: irq 16, io mem 0x56204400
[ 3.972303] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 3.972407] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.972418] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.972426] usb usb1: Product: EHCI Host Controller
[ 3.972433] usb usb1: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae ehci_hcd
[ 3.972440] usb usb1: SerialNumber: 0000:00:1d.7
[ 3.972837] hub 1-0:1.0: USB hub found
[ 3.972856] hub 1-0:1.0: 8 ports detected
[ 3.974626] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.974718] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.974738] libata version 3.00 loaded.
[ 3.974749] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.974758] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.974799] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 3.974854] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00004080
[ 3.974976] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.974987] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.974995] usb usb2: Product: UHCI Host Controller
[ 3.975002] usb usb2: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae uhci_hcd
[ 3.975009] usb usb2: SerialNumber: 0000:00:1d.0
[ 3.975388] hub 2-0:1.0: USB hub found
[ 3.975404] hub 2-0:1.0: 2 ports detected
[ 3.975619] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 3.975642] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3.975651] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.975675] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 3.975757] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00004060
[ 3.975870] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.975880] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.975888] usb usb3: Product: UHCI Host Controller
[ 3.975896] usb usb3: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae uhci_hcd
[ 3.975904] usb usb3: SerialNumber: 0000:00:1d.1
[ 3.976339] hub 3-0:1.0: USB hub found
[ 3.976357] hub 3-0:1.0: 2 ports detected
[ 3.976567] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.976594] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 3.976604] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.976629] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 3.976706] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
[ 3.976812] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.976822] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.976830] usb usb4: Product: UHCI Host Controller
[ 3.976837] usb usb4: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae uhci_hcd
[ 3.976845] usb usb4: SerialNumber: 0000:00:1d.2
[ 3.977201] hub 4-0:1.0: USB hub found
[ 3.977216] hub 4-0:1.0: 2 ports detected
[ 3.977438] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 3.977460] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 3.977469] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 3.977492] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 3.977560] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00004020
[ 3.977665] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.977674] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.977681] usb usb5: Product: UHCI Host Controller
[ 3.977688] usb usb5: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae uhci_hcd
[ 3.977695] usb usb5: SerialNumber: 0000:00:1d.3
[ 3.978050] hub 5-0:1.0: USB hub found
[ 3.978069] hub 5-0:1.0: 2 ports detected
[ 3.978869] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.978883] i915 0000:00:02.0: setting latency timer to 64
[ 4.032656] i915 0000:00:02.0: irq 44 for MSI/MSI-X
[ 4.032670] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 4.032677] [drm] Driver supports precise vblank timestamp query.
[ 4.032786] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 4.284149] usb 1-6: new high-speed USB device number 2 using ehci_hcd
[ 4.365147] [drm] initialized overlay support
[ 4.385085] fbcon: inteldrmfb (fb0) is primary device
[ 4.460090] usb 1-6: New USB device found, idVendor=5986, idProduct=0314
[ 4.460098] usb 1-6: New USB device strings: Mfr=2, Product=3, SerialNumber=0
[ 4.460104] usb 1-6: Product: HP Webcam
[ 4.460108] usb 1-6: Manufacturer: GenesysLogic Technology Co., Ltd.
[ 4.696133] usb 1-8: new high-speed USB device number 4 using ehci_hcd
[ 4.754924] Console: switching to colour frame buffer device 128x37
[ 4.761761] fb0: inteldrmfb frame buffer device
[ 4.761765] drm: registered panic notifier
[ 4.770463] acpi device:15: registered as cooling_device0
[ 4.771034] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 4.771053] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
[ 4.771147] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.771203] ahci 0000:00:1f.2: version 3.0
[ 4.771227] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 4.771333] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
[ 4.771520] ahci: SSS flag set, parallel bus scan disabled
[ 4.771573] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x1 impl SATA mode
[ 4.771585] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part
[ 4.771599] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.779958] scsi0 : ahci
[ 4.780537] scsi1 : ahci
[ 4.780976] scsi2 : ahci
[ 4.781420] scsi3 : ahci
[ 4.781647] ata1: SATA max UDMA/133 abar m1024@0x56204000 port 0x56204100 irq 45
[ 4.781657] ata2: DUMMY
[ 4.781663] ata3: DUMMY
[ 4.781668] ata4: DUMMY
[ 4.835419] usb 1-8: New USB device found, idVendor=03f0, idProduct=301d
[ 4.835433] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.835444] usb 1-8: Product: lc2000
[ 4.835452] usb 1-8: Manufacturer: ðlc2000
[ 4.835463] usb 1-8: SerialNumber: 3519120400366430
[ 5.084136] usb 5-1: new full-speed USB device number 2 using uhci_hcd
[ 5.258679] usb 5-1: New USB device found, idVendor=0a5c, idProduct=21b4
[ 5.258693] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.258703] usb 5-1: Product: Broadcom 2070 Bluetooth
[ 5.258712] usb 5-1: Manufacturer: Broadcom Corp
[ 5.258724] usb 5-1: SerialNumber: CC52AF190392
[ 5.272069] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 5.272986] ata1.00: ATA-8: ST9250410AS, 0006HPM1, max UDMA/100
[ 5.272999] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 5.274057] ata1.00: configured for UDMA/100
[ 5.274329] scsi 0:0:0:0: Direct-Access ATA ST9250410AS 0006 PQ: 0 ANSI: 5
[ 5.284866] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 5.285081] sd 0:0:0:0: [sda] Write Protect is off
[ 5.285092] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.285184] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.356783] sda: sda1 sda2 < sda5 sda6 >
[ 5.357984] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.361829] thermal LNXTHERM:00: registered as thermal_zone0
[ 5.361836] ACPI: Thermal Zone [CPUZ] (52 C)
[ 5.364393] thermal LNXTHERM:01: registered as thermal_zone1
[ 5.364402] ACPI: Thermal Zone [BATZ] (37 C)
[ 6.320544] PM: Starting manual resume from disk
[ 6.320553] PM: Hibernation image partition 8:5 present
[ 6.320558] PM: Looking for hibernation image.
[ 6.321039] PM: Image not found (code -22)
[ 6.321043] PM: Hibernation image not present or could not be loaded.
[ 6.407454] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 8.245376] udev[310]: starting version 164
[ 9.129200] Bluetooth: Core ver 2.16
[ 9.129261] NET: Registered protocol family 31
[ 9.129269] Bluetooth: HCI device and connection manager initialized
[ 9.129278] Bluetooth: HCI socket layer initialized
[ 9.129284] Bluetooth: L2CAP socket layer initialized
[ 9.130848] Bluetooth: SCO socket layer initialized
[ 9.143520] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9.143636] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[ 9.143703] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 9.256781] wmi: Mapper loaded
[ 9.309459] cdc_wdm 1-8:1.5: cdc-wdm-176: USB WDM device
[ 9.309631] cdc_wdm 1-8:1.8: cdc-wdm-175: USB WDM device
[ 9.309697] usbcore: registered new interface driver cdc_wdm
[ 9.310432] cdc_acm 1-8:1.1: ttyACM0: USB ACM device
[ 9.317571] cdc_acm 1-8:1.3: ttyACM1: USB ACM device
[ 9.333543] cdc_acm 1-8:1.9: ttyACM2: USB ACM device
[ 9.349138] usbcore: registered new interface driver cdc_acm
[ 9.349147] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 9.393450] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input5
[ 9.408608] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 9.409516] cfg80211: Calling CRDA to update world regulatory domain
[ 9.409828] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 9.411166] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 9.438126] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 9.449331] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 9.449734] usbcore: registered new interface driver btusb
[ 9.485530] Linux media interface: v0.10
[ 9.508387] Linux video capture interface: v2.00
[ 9.536380] uvcvideo: Found UVC 1.00 device HP Webcam (5986:0314)
[ 9.544250] input: HP Webcam as /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/input/input9
[ 9.545360] usbcore: registered new interface driver uvcvideo
[ 9.545370] USB Video Class driver (1.1.1)
[ 9.587966] ACPI: AC Adapter [AC] (on-line)
[ 9.633274] ACPI: Battery Slot [BAT0] (battery present)
[ 9.637719] input: HP WMI hotkeys as /devices/virtual/input/input10
[ 9.751489] cdc_ether 1-8:1.6: wwan0: register 'cdc_ether' at usb-0000:00:1d.7-8, Mobile Broadband Network Device, 02:80:37:ec:02:00
[ 9.751562] usbcore: registered new interface driver cdc_ether
[ 9.860035] brcmsmac 0000:01:00.0: bus 1 slot 0 func 0 irq 11
[ 9.860067] brcmsmac 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9.860084] brcmsmac 0000:01:00.0: setting latency timer to 64
[ 10.110963] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04773/0xa40000/0xa0400
[ 10.167958] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11
[ 10.338991] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.178546] Adding 975868k swap on /dev/sda5. Priority:-1 extents:1 across:975868k
[ 11.186206] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 11.516549] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 11.633892] loop: module loaded
[ 12.247128] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[ 13.140194] fuse init (API version 7.17)
[ 15.160999] vboxdrv: Found 2 processor cores.
[ 15.161575] vboxdrv: fAsync=0 offMin=0x1a4 offMax=0xa96
[ 15.162587] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 15.162597] vboxdrv: Successfully loaded version 4.1.14 (interface 0x00190000).
[ 15.663332] vboxpci: IOMMU not found (not registered)
[ 16.012071] ieee80211 phy0: brcms_ops_config: change monitor mode: false (implement)
[ 16.012084] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 16.012710] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 16.013266] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 16.250970] r8169 0000:03:00.0: eth0: link down
[ 16.251362] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 34.897945] wlan0: authenticate with 00:24:17:8c:df:83 (try 1)
[ 34.900242] wlan0: authenticated
[ 34.900400] wlan0: associate with 00:24:17:8c:df:83 (try 1)
[ 34.903195] wlan0: RX AssocResp from 00:24:17:8c:df:83 (capab=0x411 status=0 aid=2)
[ 34.903211] wlan0: associated
[ 34.905055] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 34.905070] ieee80211 phy0: brcmsmac: brcms_ops_bss_info_changed: associated
[ 34.905082] ieee80211 phy0: changing basic rates failed: -22
[ 34.905092] ieee80211 phy0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 0 (implement)
[ 34.905892] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 37.217873] ieee80211 phy0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement)
[ 45.160059] wlan0: no IPv6 routers presentlsmod
Module Size Used by
pci_stub 12397 1
vboxpci 18587 0
vboxnetadp 13146 0
vboxnetflt 23064 0
vboxdrv 164431 3 vboxpci,vboxnetadp,vboxnetflt
acpi_cpufreq 12773 1
mperf 12387 1 acpi_cpufreq
cpufreq_powersave 12422 0
cpufreq_stats 12711 0
cpufreq_userspace 12520 0
cpufreq_conservative 12987 0
fuse 55602 3
loop 17990 0
arc4 12418 2
joydev 16906 0
brcmsmac 450414 0
cdc_ether 12560 0
hp_wmi 13058 0
battery 12957 0
ac 12552 0
usbnet 17626 1 cdc_ether
mac80211 174497 1 brcmsmac
uvcvideo 56733 0
videodev 61494 1 uvcvideo
media 13692 2 uvcvideo,videodev
brcmutil 12785 1 brcmsmac
pcspkr 12515 0
sparse_keymap 12680 1 hp_wmi
btusb 17209 0
cfg80211 116717 2 brcmsmac,mac80211
snd_hda_codec_idt 48639 1
tpm_tis 13027 0
tpm 17545 1 tpm_tis
tpm_bios 12799 1 tpm
i2c_i801 12670 0
cdc_acm 17482 0
cdc_wdm 12904 0
power_supply 13283 2 battery,ac
wmi 13051 1 hp_wmi
crc8 12394 1 brcmsmac
evdev 17209 16
psmouse 54719 0
serio_raw 12755 0
processor 27116 1 acpi_cpufreq
cordic 12305 1 brcmsmac
snd_hda_intel 21590 1
bluetooth 106743 1 btusb
rfkill 18474 3 hp_wmi,cfg80211,bluetooth
snd_hda_codec 63039 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 12906 1 snd_hda_codec
snd_pcm 52888 2 snd_hda_intel,snd_hda_codec
snd_seq 39172 0
snd_timer 22171 2 snd_pcm,snd_seq
snd_seq_device 12995 1 snd_seq
snd 42395 10 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 12878 1 snd
snd_page_alloc 12841 2 snd_hda_intel,snd_pcm
ext4 308506 2
mbcache 12810 1 ext4
jbd2 55549 1 ext4
crc16 12327 2 bluetooth,ext4
sd_mod 35060 4
crc_t10dif 12332 1 sd_mod
ahci 20821 3
libahci 22282 1 ahci
uhci_hcd 26153 0
libata 124147 2 ahci,libahci
i915 309986 2
scsi_mod 134556 2 sd_mod,libata
ehci_hcd 34968 0
drm_kms_helper 26550 1 i915
drm 133771 3 i915,drm_kms_helper
usbcore 103522 9 cdc_ether,usbnet,uvcvideo,btusb,cdc_acm,cdc_wdm,uhci_hcd,ehci_hcd
r8169 41015 0
i2c_algo_bit 12706 1 i915
i2c_core 19022 6 videodev,i2c_i801,i915,drm_kms_helper,drm,i2c_algo_bit
mii 12595 2 usbnet,r8169
video 17345 1 i915
thermal 13058 0
button 12783 1 i915
usb_common 12338 1 usbcore
thermal_sys 17712 3 processor,video,thermalOffline
#9 2012-05-17 07:02:00
- sano
- #! CrunchBanger
- Registered: 2012-03-07
- Posts: 111
Re: My wireless disconnects constantly
I have the same card and lsmod shows "bcma" as a module used by brcmsmac - but I am on sid, and the requirements changed only recently.
Offline
#10 2012-05-17 07:27:42
- xaos52
- The Good Doctor
- From: Planet of the @s
- Registered: 2011-06-24
- Posts: 4,290
Re: My wireless disconnects constantly
Looks OK.
According to linuxwireless.org , supporting your wireless card in b43 is still a "work in progress", so brcmsmac is the way to go, I think.
Support of BCM4313 gives a mixed picture: some get it working with wl, some with b43, some with brcmsmac.
brcmsmac is still seeing some recent development and bug fixes, so perhaps using compat-wireless to compile the most recent version of brcmsmac against your kernel is worth a try? See linuxwireless.orgfor the howto. Let us know if you need help with it.
hth
PS: Find anything usefull in syslog after a disconnect?
Last edited by xaos52 (2012-05-17 07:53:33)
bootinfoscript - emacs primer - I ♥ #!
Offline
#11 2012-05-17 13:14:39
Re: My wireless disconnects constantly
PS: Find anything usefull in syslog after a disconnect?
How do I do that? :S
I have the same card and lsmod shows "bcma" as a module used by brcmsmac - but I am on sid, and the requirements changed only recently.
Once I used "Testing" and I don't want to talk about it ¬¬ hehe so I'm kind of caught ti stable hehehe
brcmsmac is still seeing some recent development and bug fixes, so perhaps using compat-wireless to compile the most recent version of brcmsmac against your kernel is worth a try? See linuxwireless.org for the howto. Let us know if you need help with it.
Is this a process that can withstand a netbook?
Offline
#12 2012-05-17 13:35:24
Re: My wireless disconnects constantly
I'm trying to compile compat-wireless. This is what i've got:
path/to/compat-wireless-3.2.5-1/net/wireless/util.c:810: error: implicit declaration of function ‘br_port_exists’my kernel is 3.2.0-0.bpo.2-686-pae
Offline
#13 2012-05-17 15:24:40
- xaos52
- The Good Doctor
- From: Planet of the @s
- Registered: 2011-06-24
- Posts: 4,290
Re: My wireless disconnects constantly
I just compiled it on my system - same kernel - got no errors.
Here are the steps:
(1) download bleeding edge compat wireless from this page http://linuxwireless.org/en/users/Downl … eding_edge
(2) untar the archive
(3) cd to the uncompressed dir
(4)
./scripts/driver-select brcmsmac(5)
make(6)
sudo make install(7) reboot
Last edited by xaos52 (2012-05-17 15:26:11)
bootinfoscript - emacs primer - I ♥ #!
Offline
#14 2012-05-17 16:27:07
- pvsage
- Internal Affairs
- From: North Carolina
- Registered: 2009-10-18
- Posts: 9,012
Re: My wireless disconnects constantly
@nuxero: Have you tried the bpo.1 kernel? I have to use the earlier backports kernel with my Realtek wifi adapter...may be worth a shot? 
while ( ! ( succeed = try() ) );
We've earned a reputation as a nice, friendly community; please help us keep it that way.
Online
#16 2012-05-18 00:25:51
Re: My wireless disconnects constantly
@xaos52: I installed compat-wireless, no errors and reboot. Now I don't have wireless ¬¬
iwconfig
ppp0 no wireless extensions.
lo no wireless extensions.
wwan0 no wireless extensions.
eth0 no wireless extensions.dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-0.bpo.2-686-pae (Debian 3.2.15-1~bpo60+1) (debian-kernel@lists.debian.org) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Mon Apr 23 09:33:57 UTC 2012
[ 0.000000] Disabled fast string operations
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f43f000 (usable)
[ 0.000000] BIOS-e820: 000000003f43f000 - 000000003f4bf000 (reserved)
[ 0.000000] BIOS-e820: 000000003f4bf000 - 000000003f5bf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f5bf000 - 000000003f5ff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003f5ff000 - 000000003f600000 (usable)
[ 0.000000] BIOS-e820: 000000003f600000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: Hewlett-Packard HP Mini 110-3500 /1584, BIOS F.14 11/30/2010
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x3f600 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFE00000 mask 0FFE00000 write-protect
[ 0.000000] 1 base 000000000 mask 0E0000000 write-back
[ 0.000000] 2 base 020000000 mask 0E0000000 write-back
[ 0.000000] 3 base 03F800000 mask 0FF800000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01a00000
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037800000 page 2M
[ 0.000000] 0037800000 - 00379fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 379fe000 @ 19fa000-1a00000
[ 0.000000] RAMDISK: 2ea07000 - 2f770000
[ 0.000000] ACPI: RSDP 000fe020 00024 (v02 HPQOEM)
[ 0.000000] ACPI: XSDT 3f5fe120 00074 (v01 HPQOEM SLIC-MPC 00000001 01000013)
[ 0.000000] ACPI: FACP 3f5fd000 000F4 (v04 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: DSDT 3f5f2000 07DD6 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: FACS 3f583000 00040
[ 0.000000] ACPI: HPET 3f5fc000 00038 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: APIC 3f5fb000 00078 (v02 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: MCFG 3f5fa000 0003C (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: SLIC 3f5f1000 00176 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: BOOT 3f5f0000 00028 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: SSDT 3f5ef000 00628 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 3f5ee000 00259 (v01 PmRef Cpu0Tst 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 3f5ed000 0020F (v01 PmRef ApTst 00003000 INTL 20051117)
[ 0.000000] ACPI: WDAT 3f5ec000 00194 (v01 INSYDE INSYDE 00000001 MSFT 01000013)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 124MB HIGHMEM available.
[ 0.000000] 889MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 379fe000
[ 0.000000] low ram: 0 - 379fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000379fe
[ 0.000000] HighMem 0x000379fe -> 0x0003f600
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003f43f
[ 0.000000] 0: 0x0003f5ff -> 0x0003f600
[ 0.000000] On node 0 totalpages: 259023
[ 0.000000] free_area_init_node: node 0, pgdat c1424000, node_mem_map f720d200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1748 pages used for memmap
[ 0.000000] Normal zone: 221994 pages, LIFO batch:31
[ 0.000000] HighMem zone: 249 pages used for memmap
[ 0.000000] HighMem zone: 31049 pages, LIFO batch:7
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:a0000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @f7000000 s33088 r0 d24256 u524288
[ 0.000000] pcpu-alloc: s33088 r0 d24256 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256994
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-0.bpo.2-686-pae root=UUID=bcfe8b15-4150-4943-ac46-c61d0809638a ro quiet splash splash
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000379fe:0003f600)
[ 0.000000] Memory: 1007852k/1038336k available (2925k kernel code, 28240k reserved, 1344k data, 436k init, 125192k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
[ 0.000000] .init : 0xc142c000 - 0xc1499000 ( 436 kB)
[ 0.000000] .data : 0xc12db62d - 0xc142b8c0 (1344 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12db62d (2925 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:712 16
[ 0.000000] CPU 0 irqstacks, hard=f6806000 soft=f6808000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1662.468 MHz processor.
[ 0.004004] Calibrating delay loop (skipped), value calculated using timer frequency.. 3324.93 BogoMIPS (lpj=6649872)
[ 0.004015] pid_max: default: 32768 minimum: 301
[ 0.004101] Security Framework initialized
[ 0.004110] AppArmor: AppArmor disabled by boot time parameter
[ 0.004144] Mount-cache hash table entries: 512
[ 0.008101] Initializing cgroup subsys cpuacct
[ 0.008112] Initializing cgroup subsys memory
[ 0.008128] Initializing cgroup subsys devices
[ 0.008133] Initializing cgroup subsys freezer
[ 0.008138] Initializing cgroup subsys net_cls
[ 0.008143] Initializing cgroup subsys blkio
[ 0.008155] Initializing cgroup subsys perf_event
[ 0.008203] Disabled fast string operations
[ 0.008211] CPU: Physical Processor ID: 0
[ 0.008215] CPU: Processor Core ID: 0
[ 0.008220] mce: CPU supports 5 MCE banks
[ 0.008233] CPU0: Thermal monitoring enabled (TM2)
[ 0.008240] using mwait in idle threads.
[ 0.009505] ACPI: Core revision 20110623
[ 0.020100] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.020604] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.063243] CPU0: Intel(R) Atom(TM) CPU N455 @ 1.66GHz stepping 0a
[ 0.064003] Performance Events: PEBS fmt0+, Atom events, Intel PMU driver.
[ 0.064003] ... version: 3
[ 0.064003] ... bit width: 40
[ 0.064003] ... generic registers: 2
[ 0.064003] ... value mask: 000000ffffffffff
[ 0.064003] ... max period: 000000007fffffff
[ 0.064003] ... fixed-purpose events: 3
[ 0.064003] ... event mask: 0000000700000003
[ 0.064003] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.064003] CPU 1 irqstacks, hard=f68f2000 soft=f68f4000
[ 0.064003] Booting Node 0, Processors #1
[ 0.064003] smpboot cpu 1: start_ip = 9b000
[ 0.008000] Initializing CPU#1
[ 0.008000] Disabled fast string operations
[ 0.152067] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.152139] Brought up 2 CPUs
[ 0.152148] Total of 2 processors activated (6649.92 BogoMIPS).
[ 0.152708] devtmpfs: initialized
[ 0.152708] PM: Registering ACPI NVS region at 3f4bf000 (1048576 bytes)
[ 0.152708] print_constraints: dummy:
[ 0.152708] NET: Registered protocol family 16
[ 0.152817] ACPI: bus type pci registered
[ 0.152983] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.152992] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.152997] PCI: Using MMCONFIG for extended config space
[ 0.153001] PCI: Using configuration type 1 for base access
[ 0.156125] bio: create slab <bio-0> at 0
[ 0.156125] ACPI: Added _OSI(Module Device)
[ 0.156126] ACPI: Added _OSI(Processor Device)
[ 0.156131] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.156137] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.158863] ACPI: EC: Look up EC in DSDT
[ 0.164454] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.165550] ACPI: SSDT 3f497790 00731 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.166650] ACPI: Dynamic OEM Table Load:
[ 0.166658] ACPI: SSDT (null) 00731 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.166985] ACPI: SSDT 3f495690 00646 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.167644] ACPI: Dynamic OEM Table Load:
[ 0.167651] ACPI: SSDT (null) 00646 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.188674] ACPI: SSDT 3f496d90 0015F (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.189418] ACPI: Dynamic OEM Table Load:
[ 0.189425] ACPI: SSDT (null) 0015F (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.200258] ACPI: SSDT 3f496f10 0008D (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.200947] ACPI: Dynamic OEM Table Load:
[ 0.200954] ACPI: SSDT (null) 0008D (v01 PmRef ApCst 00003000 INTL 20051117)
[ 1.308203] ACPI: Interpreter enabled
[ 1.308219] ACPI: (supports S0 S3 S4 S5)
[ 1.308281] ACPI: Using IOAPIC for interrupt routing
[ 1.333951] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[ 1.334251] ACPI: No dock devices found.
[ 1.334257] HEST: Table not found.
[ 1.334267] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 1.335172] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20110623/nspredef-359)
[ 1.335191] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 1.335195] _OSC request data:1 8 1f
[ 1.335206] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 1.337123] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 1.337131] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 1.337138] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 1.337146] pci_root PNP0A08:00: host bridge window [mem 0x40000000-0xfebfffff]
[ 1.337176] pci 0000:00:00.0: [8086:a010] type 0 class 0x000600
[ 1.337240] pci 0000:00:02.0: [8086:a011] type 0 class 0x000300
[ 1.337256] pci 0000:00:02.0: reg 10: [mem 0x56180000-0x561fffff]
[ 1.337267] pci 0000:00:02.0: reg 14: [io 0x40c0-0x40c7]
[ 1.337277] pci 0000:00:02.0: reg 18: [mem 0x40000000-0x4fffffff pref]
[ 1.337288] pci 0000:00:02.0: reg 1c: [mem 0x56000000-0x560fffff]
[ 1.337342] pci 0000:00:02.1: [8086:a012] type 0 class 0x000380
[ 1.337356] pci 0000:00:02.1: reg 10: [mem 0x56100000-0x5617ffff]
[ 1.337469] pci 0000:00:1b.0: [8086:27d8] type 0 class 0x000403
[ 1.337496] pci 0000:00:1b.0: reg 10: [mem 0x56200000-0x56203fff 64bit]
[ 1.337607] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 1.337616] pci 0000:00:1b.0: PME# disabled
[ 1.337657] pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
[ 1.337773] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.337781] pci 0000:00:1c.0: PME# disabled
[ 1.337824] pci 0000:00:1c.2: [8086:27d4] type 1 class 0x000604
[ 1.337933] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 1.337942] pci 0000:00:1c.2: PME# disabled
[ 1.337984] pci 0000:00:1c.3: [8086:27d6] type 1 class 0x000604
[ 1.338094] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 1.338102] pci 0000:00:1c.3: PME# disabled
[ 1.338144] pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
[ 1.338203] pci 0000:00:1d.0: reg 20: [io 0x4080-0x409f]
[ 1.338258] pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
[ 1.338317] pci 0000:00:1d.1: reg 20: [io 0x4060-0x407f]
[ 1.338371] pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
[ 1.338429] pci 0000:00:1d.2: reg 20: [io 0x4040-0x405f]
[ 1.338483] pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
[ 1.338543] pci 0000:00:1d.3: reg 20: [io 0x4020-0x403f]
[ 1.338610] pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
[ 1.338640] pci 0000:00:1d.7: reg 10: [mem 0x56204400-0x562047ff]
[ 1.338757] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 1.338766] pci 0000:00:1d.7: PME# disabled
[ 1.338799] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 1.338900] pci 0000:00:1f.0: [8086:27bc] type 0 class 0x000601
[ 1.339080] pci 0000:00:1f.2: [8086:27c1] type 0 class 0x000106
[ 1.339108] pci 0000:00:1f.2: reg 10: [io 0x40b8-0x40bf]
[ 1.339125] pci 0000:00:1f.2: reg 14: [io 0x40cc-0x40cf]
[ 1.339140] pci 0000:00:1f.2: reg 18: [io 0x40b0-0x40b7]
[ 1.339154] pci 0000:00:1f.2: reg 1c: [io 0x40c8-0x40cb]
[ 1.339169] pci 0000:00:1f.2: reg 20: [io 0x40a0-0x40af]
[ 1.339184] pci 0000:00:1f.2: reg 24: [mem 0x56204000-0x562043ff]
[ 1.339241] pci 0000:00:1f.2: PME# supported from D3hot
[ 1.339249] pci 0000:00:1f.2: PME# disabled
[ 1.339276] pci 0000:00:1f.3: [8086:27da] type 0 class 0x000c05
[ 1.339352] pci 0000:00:1f.3: reg 20: [io 0x4000-0x401f]
[ 1.339510] pci 0000:01:00.0: [14e4:4727] type 0 class 0x000280
[ 1.339558] pci 0000:01:00.0: reg 10: [mem 0x55000000-0x55003fff 64bit]
[ 1.339793] pci 0000:01:00.0: supports D1 D2
[ 1.344119] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 1.344129] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 1.344139] pci 0000:00:1c.0: bridge window [mem 0x55000000-0x55ffffff]
[ 1.344151] pci 0000:00:1c.0: bridge window [mem 0x50000000-0x50ffffff 64bit pref]
[ 1.344214] pci 0000:00:1c.2: PCI bridge to [bus 02-02]
[ 1.344223] pci 0000:00:1c.2: bridge window [io 0x2000-0x2fff]
[ 1.344232] pci 0000:00:1c.2: bridge window [mem 0x54000000-0x54ffffff]
[ 1.344243] pci 0000:00:1c.2: bridge window [mem 0x51000000-0x51ffffff 64bit pref]
[ 1.344376] pci 0000:03:00.0: [10ec:8136] type 0 class 0x000200
[ 1.344445] pci 0000:03:00.0: reg 10: [io 0x1000-0x10ff]
[ 1.344562] pci 0000:03:00.0: reg 18: [mem 0x52004000-0x52004fff 64bit pref]
[ 1.344637] pci 0000:03:00.0: reg 20: [mem 0x52000000-0x52003fff 64bit pref]
[ 1.344943] pci 0000:03:00.0: supports D1 D2
[ 1.344949] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.344967] pci 0000:03:00.0: PME# disabled
[ 1.345147] pci 0000:00:1c.3: PCI bridge to [bus 03-03]
[ 1.345156] pci 0000:00:1c.3: bridge window [io 0x1000-0x1fff]
[ 1.345165] pci 0000:00:1c.3: bridge window [mem 0x53000000-0x53ffffff]
[ 1.345177] pci 0000:00:1c.3: bridge window [mem 0x52000000-0x52ffffff 64bit pref]
[ 1.345266] pci 0000:00:1e.0: PCI bridge to [bus 04-04] (subtractive decode)
[ 1.345284] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 1.345291] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 1.345299] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 1.345306] pci 0000:00:1e.0: bridge window [mem 0x40000000-0xfebfffff] (subtractive decode)
[ 1.345339] pci_bus 0000:00: on NUMA node 0
[ 1.345347] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.345637] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 1.345821] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 1.345950] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
[ 1.346067] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
[ 1.346331] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20110623/nspredef-359)
[ 1.346349] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 1.346353] _OSC request data:1 1f 1f
[ 1.346364] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 1.346497] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20110623/nspredef-359)
[ 1.346513] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 1.346518] _OSC request data:1 0 1d
[ 1.346528] pci0000:00: ACPI _OSC request failed (AE_TYPE), returned control mask: 0x1d
[ 1.346533] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 1.352417] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 1.352563] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12)
[ 1.352705] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 1.352847] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 1.352988] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.353136] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.353279] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.353423] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.353780] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.353780] vgaarb: loaded
[ 1.353780] vgaarb: bridge control possible 0000:00:02.0
[ 1.353780] PCI: Using ACPI for IRQ routing
[ 1.362728] PCI: pci_cache_line_size set to 64 bytes
[ 1.362846] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 1.362853] reserve RAM buffer: 000000003f43f000 - 000000003fffffff
[ 1.362860] reserve RAM buffer: 000000003f600000 - 000000003fffffff
[ 1.363123] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 1.363135] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 1.363146] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 1.368261] Switching to clocksource hpet
[ 1.371504] pnp: PnP ACPI init
[ 1.371544] ACPI: bus type pnp registered
[ 1.377597] pnp 00:00: [bus 00-ff]
[ 1.377604] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 1.377611] pnp 00:00: [io 0x0cf8-0x0cff]
[ 1.377617] pnp 00:00: [io 0x0d00-0xffff window]
[ 1.377623] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 1.377629] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 1.377636] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 1.377642] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 1.377648] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 1.377658] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 1.377664] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 1.377670] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 1.377676] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 1.377682] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 1.377689] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 1.377695] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 1.377701] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 1.377707] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 1.377714] pnp 00:00: [mem 0x40000000-0xfebfffff window]
[ 1.377840] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 1.378132] pnp 00:01: [io 0x164e-0x164f]
[ 1.378138] pnp 00:01: [io 0x0061]
[ 1.378144] pnp 00:01: [io 0x0070]
[ 1.378149] pnp 00:01: [io 0x0080]
[ 1.378154] pnp 00:01: [io 0x0092]
[ 1.378159] pnp 00:01: [io 0x00b2-0x00b3]
[ 1.378165] pnp 00:01: [io 0x0063]
[ 1.378170] pnp 00:01: [io 0x0065]
[ 1.378175] pnp 00:01: [io 0x0067]
[ 1.378180] pnp 00:01: [io 0x0600-0x060f]
[ 1.378186] pnp 00:01: [io 0x0610]
[ 1.378191] pnp 00:01: [io 0x0800-0x080f]
[ 1.378197] pnp 00:01: [io 0x0810-0x0817]
[ 1.378202] pnp 00:01: [io 0x0400-0x047f]
[ 1.378208] pnp 00:01: [io 0x0500-0x053f]
[ 1.378214] pnp 00:01: [mem 0xe0000000-0xefffffff]
[ 1.378219] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[ 1.378225] pnp 00:01: [mem 0xfed14000-0xfed17fff]
[ 1.378231] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[ 1.378237] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[ 1.378243] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[ 1.378249] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[ 1.378285] pnp 00:01: disabling [io 0x164e-0x164f] because it overlaps 0000:00:1c.3 BAR 13 [io 0x1000-0x1fff]
[ 1.378404] system 00:01: [io 0x0600-0x060f] has been reserved
[ 1.378412] system 00:01: [io 0x0610] has been reserved
[ 1.378419] system 00:01: [io 0x0800-0x080f] has been reserved
[ 1.378426] system 00:01: [io 0x0810-0x0817] has been reserved
[ 1.378433] system 00:01: [io 0x0400-0x047f] has been reserved
[ 1.378441] system 00:01: [io 0x0500-0x053f] has been reserved
[ 1.378449] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[ 1.378457] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 1.378465] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[ 1.378473] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 1.378480] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 1.378488] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 1.378496] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 1.378505] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.378531] pnp 00:02: [io 0x0000-0x001f]
[ 1.378537] pnp 00:02: [io 0x0081-0x0091]
[ 1.378543] pnp 00:02: [io 0x0093-0x009f]
[ 1.378548] pnp 00:02: [io 0x00c0-0x00df]
[ 1.378554] pnp 00:02: [dma 4]
[ 1.378629] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 1.378691] pnp 00:03: [io 0x0070-0x0077]
[ 1.378770] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.378797] pnp 00:04: [irq 0 disabled]
[ 1.378816] pnp 00:04: [irq 8]
[ 1.378822] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 1.378893] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.378922] pnp 00:05: [io 0x00f0]
[ 1.378934] pnp 00:05: [irq 13]
[ 1.379011] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 1.379040] pnp 00:06: [mem 0xff800000-0xffffffff]
[ 1.379113] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[ 1.379167] pnp 00:07: [io 0x0060]
[ 1.379176] pnp 00:07: [io 0x0064]
[ 1.379187] pnp 00:07: [irq 1]
[ 1.379265] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 1.379313] pnp 00:08: [irq 12]
[ 1.379391] pnp 00:08: Plug and Play ACPI device, IDs SYN1e3c PNP0f13 (active)
[ 1.379506] pnp: PnP ACPI: found 9 devices
[ 1.379510] ACPI: ACPI bus type pnp unregistered
[ 1.379517] PnPBIOS: Disabled by ACPI PNP
[ 1.420827] PCI: max bus depth: 1 pci_try_num: 2
[ 1.420887] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 1.420896] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 1.420906] pci 0000:00:1c.0: bridge window [mem 0x55000000-0x55ffffff]
[ 1.420916] pci 0000:00:1c.0: bridge window [mem 0x50000000-0x50ffffff 64bit pref]
[ 1.420928] pci 0000:00:1c.2: PCI bridge to [bus 02-02]
[ 1.420936] pci 0000:00:1c.2: bridge window [io 0x2000-0x2fff]
[ 1.420946] pci 0000:00:1c.2: bridge window [mem 0x54000000-0x54ffffff]
[ 1.420955] pci 0000:00:1c.2: bridge window [mem 0x51000000-0x51ffffff 64bit pref]
[ 1.420967] pci 0000:00:1c.3: PCI bridge to [bus 03-03]
[ 1.420974] pci 0000:00:1c.3: bridge window [io 0x1000-0x1fff]
[ 1.420984] pci 0000:00:1c.3: bridge window [mem 0x53000000-0x53ffffff]
[ 1.420994] pci 0000:00:1c.3: bridge window [mem 0x52000000-0x52ffffff 64bit pref]
[ 1.421006] pci 0000:00:1e.0: PCI bridge to [bus 04-04]
[ 1.421053] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.421064] pci 0000:00:1c.0: setting latency timer to 64
[ 1.421086] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.421096] pci 0000:00:1c.2: setting latency timer to 64
[ 1.421117] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 1.421125] pci 0000:00:1c.3: setting latency timer to 64
[ 1.421139] pci 0000:00:1e.0: setting latency timer to 64
[ 1.421148] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.421154] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.421160] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.421167] pci_bus 0000:00: resource 7 [mem 0x40000000-0xfebfffff]
[ 1.421174] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
[ 1.421180] pci_bus 0000:01: resource 1 [mem 0x55000000-0x55ffffff]
[ 1.421187] pci_bus 0000:01: resource 2 [mem 0x50000000-0x50ffffff 64bit pref]
[ 1.421194] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 1.421200] pci_bus 0000:02: resource 1 [mem 0x54000000-0x54ffffff]
[ 1.421207] pci_bus 0000:02: resource 2 [mem 0x51000000-0x51ffffff 64bit pref]
[ 1.421214] pci_bus 0000:03: resource 0 [io 0x1000-0x1fff]
[ 1.421220] pci_bus 0000:03: resource 1 [mem 0x53000000-0x53ffffff]
[ 1.421227] pci_bus 0000:03: resource 2 [mem 0x52000000-0x52ffffff 64bit pref]
[ 1.421234] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
[ 1.421240] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
[ 1.421247] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.421253] pci_bus 0000:04: resource 7 [mem 0x40000000-0xfebfffff]
[ 1.421388] NET: Registered protocol family 2
[ 1.421542] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1.422163] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.423094] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 1.423524] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.423530] TCP reno registered
[ 1.423540] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.423560] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.423814] NET: Registered protocol family 1
[ 1.423855] pci 0000:00:02.0: Boot video device
[ 1.423900] pci 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.423925] pci 0000:00:1d.0: PCI INT A disabled
[ 1.423958] pci 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.423981] pci 0000:00:1d.1: PCI INT B disabled
[ 1.424041] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.424065] pci 0000:00:1d.2: PCI INT C disabled
[ 1.424083] pci 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 1.424107] pci 0000:00:1d.3: PCI INT D disabled
[ 1.424124] pci 0000:00:1d.7: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.024032] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 3.024155] pci 0000:00:1d.7: PCI INT A disabled
[ 3.024192] PCI: CLS 64 bytes, default 64
[ 3.024314] Unpacking initramfs...
[ 3.739047] Freeing initrd memory: 13732k freed
[ 3.749895] Simple Boot Flag at 0x44 set to 0x1
[ 3.750832] audit: initializing netlink socket (disabled)
[ 3.750857] type=2000 audit(1337300434.744:1): initialized
[ 3.779583] highmem bounce pool size: 64 pages
[ 3.779595] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 3.784516] VFS: Disk quotas dquot_6.5.2
[ 3.784591] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.784736] msgmni has been set to 1750
[ 3.785098] alg: No test for stdrng (krng)
[ 3.785172] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.785180] io scheduler noop registered
[ 3.785184] io scheduler deadline registered
[ 3.785218] io scheduler cfq registered (default)
[ 3.785391] pcieport 0000:00:1c.0: setting latency timer to 64
[ 3.785473] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 3.785608] pcieport 0000:00:1c.2: setting latency timer to 64
[ 3.785680] pcieport 0000:00:1c.2: irq 41 for MSI/MSI-X
[ 3.785807] pcieport 0000:00:1c.3: setting latency timer to 64
[ 3.785878] pcieport 0000:00:1c.3: irq 42 for MSI/MSI-X
[ 3.786065] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 3.786133] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 3.786139] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 3.786679] intel_idle: MWAIT substates: 0x20220
[ 3.786696] intel_idle: v0.4 model 0x1C
[ 3.786700] intel_idle: lapic_timer_reliable_states 0x2
[ 3.786706] Marking TSC unstable due to TSC halts in idle states deeper than C2
[ 3.786793] ERST: Table is not found!
[ 3.786797] GHES: HEST is not enabled!
[ 3.786829] isapnp: Scanning for PnP cards...
[ 4.140778] isapnp: No Plug & Play device found
[ 4.140948] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 4.144783] Linux agpgart interface v0.103
[ 4.145011] agpgart-intel 0000:00:00.0: Intel GMA3150 Chipset
[ 4.145218] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
[ 4.145474] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[ 4.145733] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x40000000
[ 4.146074] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 4.154831] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.154846] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 4.155202] mousedev: PS/2 mouse device common for all mice
[ 4.155463] rtc_cmos 00:03: RTC can wake from S4
[ 4.155660] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 4.155701] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 4.155927] cpuidle: using governor ladder
[ 4.156257] cpuidle: using governor menu
[ 4.156819] TCP cubic registered
[ 4.156935] NET: Registered protocol family 10
[ 4.158222] Mobile IPv6
[ 4.158228] NET: Registered protocol family 17
[ 4.158239] Registering the dns_resolver key type
[ 4.158284] Using IPI No-Shortcut mode
[ 4.158601] PM: Hibernation image not present or could not be loaded.
[ 4.158628] registered taskstats version 1
[ 4.161557] rtc_cmos 00:03: setting system clock to 2012-05-18 00:20:35 UTC (1337300435)
[ 4.161718] Initializing network drop monitor service
[ 4.161964] Freeing unused kernel memory: 436k freed
[ 4.162341] Write protecting the kernel text: 2928k
[ 4.162405] Write protecting the kernel read-only data: 1088k
[ 4.162411] NX-protecting the kernel data: 3216k
[ 4.163619] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 4.194611] udev[49]: starting version 164
[ 4.332510] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 4.332527] ACPI: Power Button [PWRB]
[ 4.332768] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 4.344384] ACPI: Lid Switch [LID]
[ 4.344647] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 4.344662] ACPI: Power Button [PWRF]
[ 4.361808] usbcore: registered new interface driver usbfs
[ 4.361884] usbcore: registered new interface driver hub
[ 4.362034] usbcore: registered new device driver usb
[ 4.363777] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.363849] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.363898] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 4.363909] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.363984] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 4.368252] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 4.368278] ehci_hcd 0000:00:1d.7: debug port 1
[ 4.372173] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 4.380499] SCSI subsystem initialized
[ 4.393256] ehci_hcd 0000:00:1d.7: irq 16, io mem 0x56204400
[ 4.417823] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 4.417880] r8169 0000:03:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 4.417942] r8169 0000:03:00.0: setting latency timer to 64
[ 4.418043] r8169 0000:03:00.0: irq 43 for MSI/MSI-X
[ 4.419656] r8169 0000:03:00.0: eth0: RTL8105e at 0xf822e000, 98:4b:e1:f0:b6:45, XID 00a00000 IRQ 43
[ 4.421783] libata version 3.00 loaded.
[ 4.424069] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 4.424138] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.424149] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.424157] usb usb1: Product: EHCI Host Controller
[ 4.424165] usb usb1: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae ehci_hcd
[ 4.424172] usb usb1: SerialNumber: 0000:00:1d.7
[ 4.424554] hub 1-0:1.0: USB hub found
[ 4.424572] hub 1-0:1.0: 8 ports detected
[ 4.426364] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.426465] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.426492] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 4.426503] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 4.426538] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 4.426592] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00004080
[ 4.426706] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.426717] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.426725] usb usb2: Product: UHCI Host Controller
[ 4.426732] usb usb2: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae uhci_hcd
[ 4.426740] usb usb2: SerialNumber: 0000:00:1d.0
[ 4.427126] hub 2-0:1.0: USB hub found
[ 4.427143] hub 2-0:1.0: 2 ports detected
[ 4.427373] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 4.427400] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 4.427410] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 4.427439] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 4.427524] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00004060
[ 4.427638] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.427648] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.427656] usb usb3: Product: UHCI Host Controller
[ 4.427663] usb usb3: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae uhci_hcd
[ 4.427670] usb usb3: SerialNumber: 0000:00:1d.1
[ 4.428105] hub 3-0:1.0: USB hub found
[ 4.428125] hub 3-0:1.0: 2 ports detected
[ 4.428360] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 4.428388] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 4.428399] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.428431] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 4.428513] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
[ 4.428626] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.428636] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.428644] usb usb4: Product: UHCI Host Controller
[ 4.428652] usb usb4: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae uhci_hcd
[ 4.428659] usb usb4: SerialNumber: 0000:00:1d.2
[ 4.429816] hub 4-0:1.0: USB hub found
[ 4.429835] hub 4-0:1.0: 2 ports detected
[ 4.430070] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 4.430097] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 4.430107] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 4.430152] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 4.430237] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00004020
[ 4.430353] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.430363] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.430371] usb usb5: Product: UHCI Host Controller
[ 4.430378] usb usb5: Manufacturer: Linux 3.2.0-0.bpo.2-686-pae uhci_hcd
[ 4.430386] usb usb5: SerialNumber: 0000:00:1d.3
[ 4.430756] hub 5-0:1.0: USB hub found
[ 4.430774] hub 5-0:1.0: 2 ports detected
[ 4.431295] ahci 0000:00:1f.2: version 3.0
[ 4.431323] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 4.431431] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
[ 4.431613] ahci: SSS flag set, parallel bus scan disabled
[ 4.431666] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x1 impl SATA mode
[ 4.431679] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part
[ 4.431693] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.437090] scsi0 : ahci
[ 4.443829] [drm] Initialized drm 1.1.0 20060810
[ 4.448923] scsi1 : ahci
[ 4.468932] scsi2 : ahci
[ 4.475297] scsi3 : ahci
[ 4.475532] ata1: SATA max UDMA/133 abar m1024@0x56204000 port 0x56204100 irq 44
[ 4.475542] ata2: DUMMY
[ 4.475549] ata3: DUMMY
[ 4.475555] ata4: DUMMY
[ 4.475749] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.475762] i915 0000:00:02.0: setting latency timer to 64
[ 4.532787] i915 0000:00:02.0: irq 45 for MSI/MSI-X
[ 4.532799] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 4.532804] [drm] Driver supports precise vblank timestamp query.
[ 4.532876] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 4.740165] usb 1-6: new high-speed USB device number 2 using ehci_hcd
[ 4.850224] [drm] initialized overlay support
[ 4.869078] fbcon: inteldrmfb (fb0) is primary device
[ 4.916100] usb 1-6: New USB device found, idVendor=5986, idProduct=0314
[ 4.916107] usb 1-6: New USB device strings: Mfr=2, Product=3, SerialNumber=0
[ 4.916112] usb 1-6: Product: HP Webcam
[ 4.916117] usb 1-6: Manufacturer: GenesysLogic Technology Co., Ltd.
[ 5.008099] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 5.009020] ata1.00: ATA-8: ST9250410AS, 0006HPM1, max UDMA/100
[ 5.009031] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 5.010110] ata1.00: configured for UDMA/100
[ 5.010391] scsi 0:0:0:0: Direct-Access ATA ST9250410AS 0006 PQ: 0 ANSI: 5
[ 5.021658] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 5.021906] sd 0:0:0:0: [sda] Write Protect is off
[ 5.021915] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.022001] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.095318] sda: sda1 sda2 < sda5 sda6 >
[ 5.096520] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.152097] usb 1-8: new high-speed USB device number 4 using ehci_hcd
[ 5.287205] usb 1-8: New USB device found, idVendor=03f0, idProduct=301d
[ 5.287212] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.287218] usb 1-8: Product: lc2000
[ 5.287222] usb 1-8: Manufacturer: ðlc2000
[ 5.287226] usb 1-8: SerialNumber: 3519120400366430
[ 5.327307] Console: switching to colour frame buffer device 128x37
[ 5.334639] fb0: inteldrmfb frame buffer device
[ 5.334645] drm: registered panic notifier
[ 5.350429] acpi device:15: registered as cooling_device0
[ 5.350991] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 5.351009] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
[ 5.351103] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 5.532086] usb 5-1: new full-speed USB device number 2 using uhci_hcd
[ 5.706361] usb 5-1: New USB device found, idVendor=0a5c, idProduct=21b4
[ 5.706375] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.706386] usb 5-1: Product: Broadcom 2070 Bluetooth
[ 5.706394] usb 5-1: Manufacturer: Broadcom Corp
[ 5.706406] usb 5-1: SerialNumber: CC52AF190392
[ 5.886801] thermal LNXTHERM:00: registered as thermal_zone0
[ 5.886809] ACPI: Thermal Zone [CPUZ] (53 C)
[ 5.889814] thermal LNXTHERM:01: registered as thermal_zone1
[ 5.889821] ACPI: Thermal Zone [BATZ] (36 C)
[ 6.427694] PM: Starting manual resume from disk
[ 6.427702] PM: Hibernation image partition 8:5 present
[ 6.427706] PM: Looking for hibernation image.
[ 6.428217] PM: Image not found (code -22)
[ 6.428225] PM: Hibernation image not present or could not be loaded.
[ 6.525503] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 8.288854] udev[319]: starting version 164
[ 8.706610] wmi: Mapper loaded
[ 8.803950] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.885791] ACPI: AC Adapter [AC] (off-line)
[ 9.096600] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 9.211939] Bluetooth: Core ver 2.16
[ 9.212047] NET: Registered protocol family 31
[ 9.212055] Bluetooth: HCI device and connection manager initialized
[ 9.212063] Bluetooth: HCI socket layer initialized
[ 9.212069] Bluetooth: L2CAP socket layer initialized
[ 9.212085] Bluetooth: SCO socket layer initialized
[ 9.250581] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 9.255257] usbcore: registered new interface driver btusb
[ 9.380444] cdc_wdm 1-8:1.5: cdc-wdm-176: USB WDM device
[ 9.380739] cdc_wdm 1-8:1.8: cdc-wdm-175: USB WDM device
[ 9.381496] usbcore: registered new interface driver cdc_wdm
[ 9.381835] cdc_acm 1-8:1.1: ttyACM0: USB ACM device
[ 9.388518] cdc_acm 1-8:1.3: ttyACM1: USB ACM device
[ 9.404696] cdc_acm 1-8:1.9: ttyACM2: USB ACM device
[ 9.420322] usbcore: registered new interface driver cdc_acm
[ 9.420331] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 9.423556] ACPI: Battery Slot [BAT0] (battery present)
[ 9.436968] cdc_ether 1-8:1.6: wwan0: register 'cdc_ether' at usb-0000:00:1d.7-8, Mobile Broadband Network Device, 02:80:37:ec:02:00
[ 9.437105] usbcore: registered new interface driver cdc_ether
[ 9.471455] Linux media interface: v0.10
[ 9.518362] Linux video capture interface: v2.00
[ 9.547706] uvcvideo: Found UVC 1.00 device HP Webcam (5986:0314)
[ 9.556308] input: HP Webcam as /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/input/input6
[ 9.557291] usbcore: registered new interface driver uvcvideo
[ 9.557298] USB Video Class driver (1.1.1)
[ 9.574245] input: HP WMI hotkeys as /devices/virtual/input/input7
[ 9.642541] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9.642660] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[ 9.642733] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 9.760983] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
[ 9.776417] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 9.776710] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 10.398294] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04773/0xa40000/0xa0400
[ 10.451359] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11
[ 11.090380] Adding 975868k swap on /dev/sda5. Priority:-1 extents:1 across:975868k
[ 11.097993] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 11.428082] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 11.530596] loop: module loaded
[ 12.255911] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[ 13.159112] fuse init (API version 7.17)
[ 14.881226] vboxdrv: Found 2 processor cores.
[ 14.882329] vboxdrv: fAsync=0 offMin=0x1b8 offMax=0x24ea
[ 14.882490] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 14.882498] vboxdrv: Successfully loaded version 4.1.14 (interface 0x00190000).
[ 15.533826] vboxpci: IOMMU not found (not registered)
[ 16.115050] r8169 0000:03:00.0: eth0: link down
[ 16.115575] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 35.016915] PPP generic driver version 2.4.2
[ 35.293439] PPP BSD Compression module registered
[ 35.302747] PPP Deflate Compression module registeredlsmod
ppp_deflate 12736 0
zlib_deflate 21186 1 ppp_deflate
bsd_comp 12740 0
ppp_async 12845 1
crc_ccitt 12331 1 ppp_async
ppp_generic 21823 7 ppp_deflate,bsd_comp,ppp_async
slhc 12498 1 ppp_generic
pci_stub 12397 1
vboxpci 18587 0
vboxnetadp 13146 0
vboxnetflt 23064 0
vboxdrv 164431 3 vboxpci,vboxnetadp,vboxnetflt
acpi_cpufreq 12773 1
mperf 12387 1 acpi_cpufreq
cpufreq_powersave 12422 0
cpufreq_stats 12711 0
cpufreq_userspace 12520 0
cpufreq_conservative 12987 0
fuse 55602 3
loop 17990 0
joydev 16906 0
snd_hda_codec_idt 48639 1
snd_hda_intel 21590 1
snd_hda_codec 63039 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 12906 1 snd_hda_codec
snd_pcm 52888 2 snd_hda_intel,snd_hda_codec
hp_wmi 13058 0
snd_seq 39172 0
sparse_keymap 12680 1 hp_wmi
uvcvideo 56733 0
videodev 61494 1 uvcvideo
psmouse 54719 0
media 13692 2 uvcvideo,videodev
cdc_ether 12560 0
cdc_acm 17482 5
cdc_wdm 12904 0
usbnet 17626 1 cdc_ether
tpm_tis 13027 0
serio_raw 12755 0
evdev 17209 16
btusb 17209 0
bluetooth 106743 1 btusb
tpm 17545 1 tpm_tis
pcspkr 12515 0
tpm_bios 12799 1 tpm
rfkill 18474 2 hp_wmi,bluetooth
snd_timer 22171 2 snd_pcm,snd_seq
ac 12552 0
battery 12957 0
snd_seq_device 12995 1 snd_seq
snd 42395 10 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
i2c_i801 12670 0
power_supply 13283 2 ac,battery
processor 27116 1 acpi_cpufreq
wmi 13051 1 hp_wmi
soundcore 12878 1 snd
snd_page_alloc 12841 2 snd_hda_intel,snd_pcm
ext4 308506 2
mbcache 12810 1 ext4
jbd2 55549 1 ext4
crc16 12327 2 bluetooth,ext4
sd_mod 35060 4
crc_t10dif 12332 1 sd_mod
i915 309986 2
drm_kms_helper 26550 1 i915
drm 133771 3 i915,drm_kms_helper
ahci 20821 3
uhci_hcd 26153 0
libahci 22282 1 ahci
libata 124147 2 ahci,libahci
scsi_mod 134556 2 sd_mod,libata
i2c_algo_bit 12706 1 i915
i2c_core 19022 6 videodev,i2c_i801,i915,drm_kms_helper,drm,i2c_algo_bit
thermal 13058 0
ehci_hcd 34968 0
usbcore 103522 9 uvcvideo,cdc_ether,cdc_acm,cdc_wdm,usbnet,btusb,uhci_hcd,ehci_hcd
r8169 41015 0
mii 12595 2 usbnet,r8169
video 17345 1 i915
button 12783 1 i915
thermal_sys 17712 3 processor,thermal,video
usb_common 12338 1 usbcoreOffline
#17 2012-05-18 08:18:45
- xaos52
- The Good Doctor
- From: Planet of the @s
- Registered: 2011-06-24
- Posts: 4,290
Re: My wireless disconnects constantly
Sorry about that. These things can and do happen once in a while 
I see you are using wired connection now.
The info you posted is no help, nothing concerning wireless in there - dmesg contains only information since the last boot.
You can uninstall the compat-wireless brcmsmac driver by
(1) cd to the dir where you untarred the compat-wireless
(2) sudo make uninstall
(3) reboot
Should get you back to the previous situation - with disconnections all the time.
Can you not connect at all, or do you get frequent disconnects.
If the former, post output of
nm-toolwhile things are working.
After a disconnect, search your syslog for disconnection errors, and post the output:
sudo grep -Ei 'network|dhc|wpa|wlan' /var/log/syslogPS: You could try the wl proprietary driver: follow instructions on this link: http://wiki.debian.org/wl
Last edited by xaos52 (2012-05-18 08:30:03)
bootinfoscript - emacs primer - I ♥ #!
Offline
#19 2012-05-21 00:13:56
Re: My wireless disconnects constantly
Hi this is the info form my network:
nm-tool
NetworkManager Tool
State: connected
- Device: wlan0 [Auto Familia Zelaya] -----------------------------------------
Type: 802.11 WiFi
Driver: brcmsmac
State: connected
Default: yes
HW Address: E0:2A:82:FC:EE:AE
Capabilities:
Speed: 54 Mb/s
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points (* = current AP)
*Familia Zelaya: Infra, 00:24:17:8C:DF:83, Freq 2412 MHz, Rate 54 Mb/s, Strength 82 WPA
IPv4 Settings:
Address: 192.168.1.2
Prefix: 24 (255.255.255.0)
Gateway: 192.168.1.1
DNS: 192.168.1.1
- Device: eth0 -----------------------------------------------------------------
Type: Wired
Driver: r8169
State: unavailable
Default: no
HW Address: 98:4B:E1:F0:B6:45
Capabilities:
Carrier Detect: yes
Speed: 10 Mb/s
Wired Properties
Carrier: off
- Device: ttyACM0 --------------------------------------------------------------
Type: Mobile Broadband (GSM)
Driver: cdc_acm
State: disconnected
Default: no
Capabilities:sudo grep -Ei 'network|dhc|wpa|wlan' /var/log/syslog
May 20 18:01:34 nuxerita wpa_supplicant[1261]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
May 20 18:01:34 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: completed -> disconnected
May 20 18:01:34 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: disconnected -> scanning
May 20 18:01:35 nuxerita wpa_supplicant[1261]: Trying to associate with 00:24:17:8c:df:83 (SSID='Familia Zelaya' freq=2412 MHz)
May 20 18:01:35 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: scanning -> associating
May 20 18:01:35 nuxerita kernel: [ 1310.497277] wlan0: authenticate with 00:24:17:8c:df:83 (try 1)
May 20 18:01:35 nuxerita kernel: [ 1310.696141] wlan0: authenticate with 00:24:17:8c:df:83 (try 2)
May 20 18:01:36 nuxerita kernel: [ 1310.896093] wlan0: authenticate with 00:24:17:8c:df:83 (try 3)
May 20 18:01:36 nuxerita kernel: [ 1311.096172] wlan0: authentication with 00:24:17:8c:df:83 timed out
May 20 18:01:38 nuxerita NetworkManager[1218]: <info> (wlan0): roamed from BSSID 00:24:17:8C:DF:83 (Familia Zelaya) to (none) ((none))
May 20 18:01:45 nuxerita wpa_supplicant[1261]: Authentication with 00:24:17:8c:df:83 timed out.
May 20 18:01:45 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: associating -> disconnected
May 20 18:01:45 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: disconnected -> scanning
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 8 -> 3 (reason 11)
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> (wlan0): deactivating device (reason: 11).
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> (wlan0): canceled DHCP transaction, DHCP client pid 1691
May 20 18:01:50 nuxerita avahi-daemon[1321]: Withdrawing address record for 192.168.1.4 on wlan0.
May 20 18:01:50 nuxerita avahi-daemon[1321]: Leaving mDNS multicast group on interface wlan0.IPv4 with address 192.168.1.4.
May 20 18:01:50 nuxerita avahi-daemon[1321]: Interface wlan0.IPv4 no longer relevant for mDNS.
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) starting connection 'Auto Familia Zelaya'
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 3 -> 4 (reason 0)
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: scanning -> disconnected
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 4 -> 5 (reason 0)
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0/wireless): access point 'Auto Familia Zelaya' has security, but secrets are required.
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 5 -> 6 (reason 0)
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 6 -> 4 (reason 0)
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 4 -> 5 (reason 0)
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0/wireless): connection 'Auto Familia Zelaya' has security, and secrets exist. No new secrets needed.
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Config: added 'ssid' value 'Familia Zelaya'
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Config: added 'scan_ssid' value '1'
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Config: added 'psk' value '<omitted>'
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
May 20 18:01:50 nuxerita NetworkManager[1218]: <info> Config: set interface ap_scan to 1
May 20 18:01:51 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: disconnected -> scanning
May 20 18:02:15 nuxerita NetworkManager[1218]: <warn> Activation (wlan0/wireless): association took too long.
May 20 18:02:15 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 5 -> 6 (reason 0)
May 20 18:02:15 nuxerita NetworkManager[1218]: <warn> Activation (wlan0/wireless): asking for new secrets
May 20 18:02:15 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: scanning -> disconnected
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 6 -> 4 (reason 0)
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 4 -> 5 (reason 0)
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Activation (wlan0/wireless): connection 'Auto Familia Zelaya' has security, and secrets exist. No new secrets needed.
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Config: added 'ssid' value 'Familia Zelaya'
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Config: added 'scan_ssid' value '1'
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Config: added 'psk' value '<omitted>'
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> Config: set interface ap_scan to 1
May 20 18:02:19 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: disconnected -> scanning
May 20 18:02:44 nuxerita NetworkManager[1218]: <warn> Activation (wlan0/wireless): association took too long.
May 20 18:02:44 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 5 -> 6 (reason 0)
May 20 18:02:44 nuxerita NetworkManager[1218]: <warn> Activation (wlan0/wireless): asking for new secrets
May 20 18:02:44 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: scanning -> disconnected
May 20 18:02:54 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 6 -> 9 (reason 7)
May 20 18:02:54 nuxerita NetworkManager[1218]: <warn> Activation (wlan0) failed for access point (Familia Zelaya)
May 20 18:02:54 nuxerita NetworkManager[1218]: <info> Marking connection 'Auto Familia Zelaya' invalid.
May 20 18:02:54 nuxerita NetworkManager[1218]: <warn> Activation (wlan0) failed.
May 20 18:02:54 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 9 -> 3 (reason 0)
May 20 18:02:54 nuxerita NetworkManager[1218]: <info> (wlan0): deactivating device (reason: 0).
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) starting connection 'Auto Familia Zelaya'
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 3 -> 4 (reason 0)
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 4 -> 5 (reason 0)
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0/wireless): access point 'Auto Familia Zelaya' has security, but secrets are required.
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 5 -> 6 (reason 0)
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 6 -> 4 (reason 0)
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 4 -> 5 (reason 0)
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0/wireless): connection 'Auto Familia Zelaya' has security, and secrets exist. No new secrets needed.
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Config: added 'ssid' value 'Familia Zelaya'
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Config: added 'scan_ssid' value '1'
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Config: added 'psk' value '<omitted>'
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> Config: set interface ap_scan to 1
May 20 18:03:05 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: disconnected -> scanning
May 20 18:03:31 nuxerita NetworkManager[1218]: <warn> Activation (wlan0/wireless): association took too long.
May 20 18:03:31 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 5 -> 6 (reason 0)
May 20 18:03:31 nuxerita NetworkManager[1218]: <warn> Activation (wlan0/wireless): asking for new secrets
May 20 18:03:31 nuxerita NetworkManager[1218]: <info> (wlan0): supplicant connection state: scanning -> disconnected
May 20 18:03:46 nuxerita NetworkManager[1218]: <warn> (wlan0): link timed out.
May 20 18:03:56 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 6 -> 9 (reason 7)
May 20 18:03:56 nuxerita NetworkManager[1218]: <warn> Activation (wlan0) failed for access point (Familia Zelaya)
May 20 18:03:56 nuxerita NetworkManager[1218]: <info> Marking connection 'Auto Familia Zelaya' invalid.
May 20 18:03:56 nuxerita NetworkManager[1218]: <warn> Activation (wlan0) failed.
May 20 18:03:56 nuxerita NetworkManager[1218]: <info> (wlan0): device state change: 9 -> 3 (reason 0)
May 20 18:03:56 nuxerita NetworkManager[1218]: <info> (wlan0): deactivating device (reason: 0).Any idea???
Offline
#20 2012-05-21 09:55:52
- xaos52
- The Good Doctor
- From: Planet of the @s
- Registered: 2011-06-24
- Posts: 4,290
Re: My wireless disconnects constantly
Activation (wlan0/wireless): association took too long.
Can you try eliminating network manager: follow instructions from this post
http://crunchbanglinux.org/forums/post/171244/#p171244
Try instructions in Manual configuration, no encryption, WEP, and WPA
post the output from the wpa_supplicant command.
If it is still not working, try the ifupdown method.
Document what you have done as much as possible. Copy the commands you entered and the output they produce,and post it on the forum.
hth
EDIT: edit away any secrets before you post.
Last edited by xaos52 (2012-05-21 10:06:41)
bootinfoscript - emacs primer - I ♥ #!
Offline
#22 2012-05-22 09:27:40
- xaos52
- The Good Doctor
- From: Planet of the @s
- Registered: 2011-06-24
- Posts: 4,290
Re: My wireless disconnects constantly
So the problem is Network-Manager not brcmsmac???
I can not say that for sure until you get your wireless working without NM. Just trying to make things as simple as possible for locating where the real error is. Once we know that, we can see what solutions are possible.
It should be posssible to let NM manage only the GSM connection.
Last edited by xaos52 (2012-05-22 09:30:24)
bootinfoscript - emacs primer - I ♥ #!
Offline
#23 2012-05-22 20:25:05
Re: My wireless disconnects constantly
After a disconnect I tried the suggested post and I got this:
sudo ip link set wlan0 up
RTNETLINK answers: Unknown error 132by the way, in the network-manager interfaces list, wlan0 says "The wireless network is disabled by the physical switch" wich is not true. The physical swithch is activated :S
Offline
#24 2012-05-22 20:39:20
- xaos52
- The Good Doctor
- From: Planet of the @s
- Registered: 2011-06-24
- Posts: 4,290
Re: My wireless disconnects constantly
Install the rfkill package if you have not installed it already:
sudo apt-get install rfkillThen run
sudo rfkill listand post the output.
Eventually use the physical switch and run 'sudo rfkill list' again to see if that changed anything.
As long as the hard lock is not removed it will not work for sure.
see 'man rfkill' for how to remove a lock.
bootinfoscript - emacs primer - I ♥ #!
Offline
Help fund CrunchBang, donate to the project!
#25 2012-05-24 01:22:28
Re: My wireless disconnects constantly
Hi I was playing around with rfkill
a normal rfkill list
0: hp-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
1: hp-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: no
2: hp-wwan: Wireless WAN
Soft blocked: no
Hard blocked: no
3: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
4: phy0: Wireless LAN
Soft blocked: no
Hard blocked: noAn rfkill list with the physical switch deactivated
0: hp-wifi: Wireless LAN
Soft blocked: no
Hard blocked: yes
1: hp-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: yes
2: hp-wwan: Wireless WAN
Soft blocked: no
Hard blocked: yes
4: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yesA rfkill list after a disconnect
0: hp-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
1: hp-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: no
2: hp-wwan: Wireless WAN
Soft blocked: no
Hard blocked: no
3: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
4: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yesI've tried with sudo rfkill unblock 4 after that but nothing happen :S
Offline
Copyright © 2012 CrunchBang Linux.
Proudly powered by Debian. Hosted by Linode.
Debian is a registered trademark of Software in the Public Interest, Inc.
